- 您现在的位置：买卖IC网 > PDF目录11766 > XRT81L27IV (Exar Corporation)IC LIU EI 7CH 3.3V 128TQFP PDF资料下载
参数资料
| 型号： | XRT81L27IV |
| 厂商： | Exar Corporation |
| 文件页数： | 13/30页 |
| 文件大小： | 0K |
| 描述： | IC LIU EI 7CH 3.3V 128TQFP |
| 标准包装： | 72 |
| 应用： | DECT |
| 接口： | 串行 |
| 电源电压： | 3.3V |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
XRT81L27
á
SEVEN CHANNEL E1 LINE INTERFACE UNIT WITH CLOCK RECOVERY
REV. 1.1.0
18
1.3
OPERATION OF THE COMMAND CONTROL REGIS-
TER BITS
(ADDRESS: 0000, HEX 0X00)
TCLKP (BIT 0)
Set to a “1”, all 7 channels will sample TPOS/TNEG
data on the rising edge of TClk. It will default to a “0”,
sampling on the falling edge.
RCLKP (BIT 1)
Set to a “1”, all channels will output RPOS/RNEG re-
ceive data on the rising edge of RClk. The default val-
ue is “0” where it will output on the falling edge.
CODE (BIT 2)
If set and if the SR/DR bit is set, will select HDB3 en-
coding for Transmit and decoding for Receive on all
channels. If CODE or SR/DR bits are “0”, AMI encod-
ing/decoding is specified.
SR/DR (BIT 3)
If set, single rail mode for the DTE side TPOS in and
RPOS out signals. RNEG is used for Line Code Vio-
lation (LCV) status. Default state is “0”, selecting du-
al-rail operation.
MUTE (BIT 4)
If set, will mute the receive outputs of a channel when
the LOS condition is detected and ARAOS is not as-
serted.
EXLOS (BIT 5)
When set, will extend the number of contiguous re-
ceived zeros to 4096 before the LOS condition is de-
clared.
ARAOS (BIT 6)
When set this bit enables insertion of “all ones data”
at RPOS/RNEG when LOS is detected on that chan-
nel.
1.4
CHANNEL CONTROL REGISTERS
These registers provide a channel by channel control
of the operation and diagnostic mode of the chip. An
individual or combination of the channels can be con-
trolled. Certain combinations of modes can not be set
as pointed out in the descriptions.
LLB[6:0] (ADDRESS 0001)
Setting a bit in this register causes that channel’s
transmit input data to be sent back out of the RPOS/
RNEG receive port. The transmit data will continue to
be sent to the line unless the TAOS control is en-
abled.
RLB[6:0] (ADDRESS 0010)
Setting a bit in this register causes that channel’s re-
ceive data to be sent back out of the TTIP/TRING on
the line to the Remote end. The receive data will con-
tinue to be sent to the DTE unless the RAOS control
is enabled.
ALBX (ADDRESS 0011)
Setting a bit in this register will cause the analog sig-
nal at the output to be sent back through the receive
section to the DTE equipment. This will effectively ex-
ercise most of the internal functions of that channel.
The Analog loopback has priority over the other loop-
back modes.
TAOS[6:0] (ADDRESS 0100)
Setting this bit enables transmitting all ones data. A
Remote loopback (RLB) on the channel has priority
over this function.
RAOS[6:0] (ADDRESS 0101)
Setting this bit inserts all ones into the receive data
stream. Local loopback has priority over RAOS and
the ARAOS signal.
PDTX[6:0] (ADDRESS 0110)
Setting this bit places the Transmit driver into a high
impedance state. Individual pin control is also avail-
able in both the Host and Hardware modes. Care
should be taken in the usage of this feature. While the
default (reset) state of this register is zero, hence en-
abling the outputs of the channel, the “PDT” pin has
TABLE 16: PDTX REGISTERS - ADDRESS: 0110, HEX 0X06
BIT NO.NAME
FUNCTION
REGISTER TYPE
0-6
PDTx0-
PDTx6
Power-down Transmitter:
Writing a "1" to this bit shut down the transmitter channel selected and places
the TTIP/TRing driver in high impedance mode. Individual pin control is also
available to switch off the transmitter for fast redundancy application both in
Host and Hardware mode.
R/W
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473T20A35S | CONN PLUG 79POS STRAIGHT W/SCKT |
| 413990-2 | CONN JACK SMB VERTICAL NICKEL |
| 5226978-1 | CONN JACK BNC RT/ANG 50 OHM TIN |
| D38999/24FB99SN | CONN RCPT 7POS JAM NUT W/SCKT |
| 1-5225398-5 | CONN JACK BNC RD316DB DUAL CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT81L27IV-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XR-T8205CP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telephone Ringer |
| XR-T8205P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telephone Ringer |
| XRT82D20 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
| XRT82D20_06 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
发布紧急采购，3分钟左右您将得到回复。