- 您现在的位置：买卖IC网 > PDF目录11766 > XRT81L27IV (Exar Corporation)IC LIU EI 7CH 3.3V 128TQFP PDF资料下载
参数资料
| 型号： | XRT81L27IV |
| 厂商： | Exar Corporation |
| 文件页数： | 8/30页 |
| 文件大小： | 0K |
| 描述： | IC LIU EI 7CH 3.3V 128TQFP |
| 标准包装： | 72 |
| 应用： | DECT |
| 接口： | 串行 |
| 电源电压： | 3.3V |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
XRT81L27
á
SEVEN CHANNEL E1 LINE INTERFACE UNIT WITH CLOCK RECOVERY
REV. 1.1.0
14
Once the CS input pin has been asserted, the type of
operation and the target register address must be
specified. This information is supplied to the MSI by
writing eight serial bits of information into the SDI in-
put. Each of these bits is clocked into the MSI from
the SDI input on the rising edge of SCLK. These eight
bits are identified and described next.
Bit 1 - R/W (Read/Write) Bit
This bit is clocked into the SDI input on the first rising
edge of SCLK after CS has been asserted. This bit
indicates whether the current operation is a Read or
Write operation. A “1” in this bit specifies a Read from
the XRT81L27, a “0” in this bit specifies a Write to the
device.
Bits 2 through 5: The four (4) bit Address Values
(labeled A0, A1, A2 and A3)
The next four rising edges of the SCLK provide the 4-
bit address value for this operation. The address se-
lects the appropriate Command/Control Register in
the XRT81L27. The address bits must be supplied to
the SDI input pin in ascending order with the LSB
(least significant bit) first.
Bits 6 and 7:
The next two bits, (A4 and A5) must be set to “0” as
shown in Figure 6.
Bit 8:
The value of A6 is a “don’t care” but must be clocked.
1.1.2
Data phase of the (MSI) operation
The Microprocessor Serial Interface (MSI) must next
be supplied with 8 additional clocks with the relative
for both the selection and data phases of the MSI op-
eration. If the operation specified is a Read, the
XRT81L27 will output data on the SDO pin from the
addressed register. Data is output in ascending order
with the LSB first
If a Write operation has been activated, the external
hardware/Micro must supply the first seven (7) bits to
be written into the selected register. The eighth bit is
a “Don’t care” as only seven bits are used in each of
the registers. These bits are input LSB first.
At the end of the serial shift phase the data is loaded
in parallel into the addressed register. If any register
bit was already set, that bit must be included in the in-
put bit stream. Therefore one must either keep an im-
age of the register status in the micro or do a “read-
modify-write” operation to maintain the state of each
bit that isn’t changing.
FIGURE 5. TIMING DIAGRAM FOR THE MICROPROCESSOR SERIAL INTERFACE
SDI
R/W
A1
A0
CS
SCLK
CS
SCLK
SDI
SDO
D0
D1
D2
D7
t22
t21
t23
t24
t25
t26
t27
t28
t29
t30
t31
t32
t33
Hi-Z
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473T20A35S | CONN PLUG 79POS STRAIGHT W/SCKT |
| 413990-2 | CONN JACK SMB VERTICAL NICKEL |
| 5226978-1 | CONN JACK BNC RT/ANG 50 OHM TIN |
| D38999/24FB99SN | CONN RCPT 7POS JAM NUT W/SCKT |
| 1-5225398-5 | CONN JACK BNC RD316DB DUAL CRIMP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT81L27IV-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XR-T8205CP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telephone Ringer |
| XR-T8205P | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telephone Ringer |
| XRT82D20 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
| XRT82D20_06 | 制造商:EXAR 制造商全称:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
发布紧急采购，3分钟左右您将得到回复。