参数资料
| 型号： | XRT83SH38IB |
| 厂商： | Exar Corporation |
| 文件页数： | 9/78页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH T1/E1/J1 8CH 225BGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 225-BGA |
| 供应商设备封装： | 225-BGA（19x19） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页
XRT83SH38
14
REV. 1.0.7
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
ALARM FUNCTIONS/REDUNDANCY SUPPORT
SIGNAL NAME
BGA
LEAD #
TYPE
DESCRIPTION
GAUGE
J18
I
Twisted Pair Cable Wire Gauge Select
Hardware Mode Only
This pin is used to match the frequency characteristics according to the gauge of
wire used in Telecom circuits. By default, the LIU is matched to 22 gauge or 24
gauge wire. To select 26 gauge, this pin must be pulled "High".
NOTE: Internally pulled “Low” with a 50k
resistor.
DMO0
DMO1
DMO2
DMO3
DMO4
DMO5
DMO6
DMO7
D5
D4
C15
C13
R5
P4
U17
V14
O
Digital Monitor Output
When no transmit output pulse is detected for more than 128 TCLK cycles within the
transmit output buffer, the DMO pin will go "High" for a minimum of one TCLK cycle.
DMO will remain "High" until the transmitter sends a valid pulse.
NOTE: This pin can be used for redundancy applications to initiate an automatic
switch to a backup card.
RESET
T8
I
Hardware Reset Input
Active low signal. When this pin is pulled "Low" for more than 10S, the internal reg-
isters are set to their default state. See the register description for the default val-
ues.
NOTE: Internally pulled "High" with a 50K
resistor.
SR/DR
K4
I
Single-Rail/Dual-Rail Data Format
Hardware Mode Only
This pin is used to control the data format on the facility side of the LIU to interface to
a Framer or Mapper/ASIC device. By default, dual rail mode is selected which relies
upon the Framer to handle the encoding/decoding functions. To select single rail
mode, this pin must be pulled "High". If single rail mode is selected, the LIU can
encode/decode AMI or B8ZS/HDB3 data formats.
NOTE: Internally pulled “Low” with a 50k
resistor.
RXTSEL
U11
I
Receiver Termination Select
Hardware Mode
This pin is used to select between the internal and external impedance modes for
the receive path. By default, the receivers are configured for external impedance
mode, which is ideal for redundancy applications without relays. To select internal
impedance, this pin must be pulled "HIgh".
Host Mode
Internal/External impedance can be selected by programming the appropriate chan-
nel registers. However, to assist in redundancy applications, this pin can be used for
a hard switch if the RxTCNTL bit is set "High" in the appropriate global register. If
RxTCNTL is set "High", the individual RxTSEL register bits are ignored.
NOTE: This pin is internally pulled “Low” with a 50k
resistor.
TXTSEL
V11
I
Transmitter Termination Select
Hardware Mode
This pin is used to select between the internal and external impedance modes for
the transmit path. By default, the receivers are configured for external impedance
mode, which is ideal for redundancy applications without relays. To select internal
impedance, this pin must be pulled "HIgh".
NOTE: This pin is internally pulled "Low".
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468E19B35P | CONN RCPT 66POS JAM NUT W/PINS |
| VI-23M-MY | CONVERTER MOD DC/DC 10V 50W |
| IDT72841L10PFG | IC FIFO SYNC 4KX9 10NS 64QFP |
| MS27473T22F21SA | CONN PLUG 21POS STRAIGHT W/SCKT |
| VI-23M-IU-F2 | CONVERTER MOD DC/DC 10V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SH38IB-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL216 | 制造商:EXAR 制造商全称:EXAR 功能描述:16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL216_06 | 制造商:EXAR 制造商全称:EXAR 功能描述:16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL216ES | 功能描述:外围驱动器与原件 - PCI 16 CH E1 LIU SH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL216IB | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。