- 您现在的位置：买卖IC网 > PDF目录48109 > YS12S10-D (POWER-ONE INC) DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | YS12S10-D |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封装： | MODULE-6 |
| 文件页数： | 24/27页 |
| 文件大小： | 332K |
| 代理商： | YS12S10-D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页
MCD10206 Rev. 1.0, 24-Jun-10
Page 6 of 27
www.power-one.com
YS12S10 DC-DC Converter Data Sheet
9.6-14 VDC Input; 0.7525-5.5 VDC Programmable @ 10 A
Because the sense lead carries minimal current,
large traces on the end-user board are not required.
However, sense trace should be located close to a
ground plane to minimize system noise and ensure
the optimum performance.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
When using remote sense, the output voltage at the
converter can be increased up to 0.5 V above the
nominal rating in order to maintain the required
voltage across the load. Therefore, the designer
must, if necessary, decrease the maximum current
(originally obtained from the derating curves) by the
same percentage to ensure the converter’s actual
output power remains at or below the maximum
allowable output power.
Output Voltage Programming (Pin 3)
The output voltage can be programmed from
0.7525 to 5.5 V by connecting an external resistor
between TRIM pin (Pin 3) and GND pin (Pin 5); see
Fig. C. Note that when trim resistor is not connected,
output voltage of the converter is 0.7525 V.
A trim resistor, RTRIM, for a desired output voltage
can be calculated using the following equation:
1
0.7525)
-
(V
5
.
10
R
REQ
-
O
RIM
T
[k]
where,
TRIM
R
Required value of trim resistor [k]
REQ
O
V
Desired (trimmed) output voltage [V]
Rload
Vin
R T-INCR
Converter
Vin
GND
ON/OFF
SENSE
(Top View)
TRIM
Vout
Y-Series
Fig. C: Configuration for programming output voltage.
Note that the tolerance of a trim resistor directly
affects
the
output
voltage
tolerance.
It
is
recommended to use standard 1% or 0.5% resistors;
for tighter tolerance, two resistors in parallel are
recommended rather than one standard value from
Table 1.
The ground pin of the trim resistor should be
connected directly to the converter GND pin (Pin 5)
with no voltage drop in between. Table 1 provides
the trim resistor values for popular output voltages.
Table 1: Trim Resistor Value
V0-REG [V]
RTRIM [k]
The Closest
Standard Value [k]
0.7525
open
1.0
41.42
41.2
1.2
22.46
22.6
1.5
13.05
13.0
1.8
9.02
9.09
2.0
7.42
7.50
2.5
5.01
4.99
3.3
3.12
3.09
5.0
1.47
5.5
1.21
The output voltage can also be programmed by
external voltage source. To make trimming less
sensitive, a series external resistor REXT is
recommended between TRIM pin and programming
voltage source. Control Voltage can be calculated by
the formula:
15
0.7525)
-
)(V
R
1
(
7
.
0
V
REQ
-
O
EXT
CTRL
[V]
where
CTRL
V
Control voltage [V]
EXT
R
External resistor between TRIM pin and
voltage source; the k value can be chosen
depending on the required output voltage range.
Control voltages with
EXT
R
0 and
EXT
R
15 k are
shown in Table 2.
Table 2: Control Voltage [VDC]
V0-REG [V]
VCTRL (REXT = 0)
VCTRL(REXT = 15 k)
0.7525
0.700
1.0
0.684
0.436
1.2
0.670
0.223
1.5
0.650
-0.097
1.8
0.630
-0.417
2.0
0.617
-0.631
2.5
0.584
-1.164
3.3
0.530
-2.017
5.0
0.417
-3.831
5.5
0.384
-4.364
相关PDF资料 |
PDF描述 |
|---|---|
| YS12S16-0G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YS12S16-0 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YS12S16-DG | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YS12S16-D | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| YSF224B-D | DSP-DIGITAL FILTER, PDIP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| YS12S10-DG | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YS12S16 | 制造商:Power-One 功能描述:DC-DC Converter, 9.6-14 VDC In., 0.7525-5.5 VDC Programmable @ 16 A, RoHS |
| YS12S16-0 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YS12S16-0G | 功能描述:DC/DC转换器 0.7525-5.5Vout 16A 9.6-14Vin RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| YS12S16-0G-Q | 功能描述:DC/DC CONVERTER 0.7525-5.5V 88W 制造商:bel power solutions 系列:Y 包装:剪切带（CT） 零件状态:停产 类型:非隔离 PoL 模块 输出数:1 电压 - 输入（最小值）:9.6V 电压 - 输入（最大值）:14V 电压 - 输出 1:0.7525 ~ 5.5 V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:16A 功率（W） - 制造系列:88W 电压 - 隔离:- 应用:ITE（商业） 特性:远程开/关，OCP，OTP，UVLO 安装类型:表面贴装 封装/外壳:6-SMD 模块 大小/尺寸:1.30" 长 x 0.53" 宽 x 0.33" 高（33.0mm x 13.5mm x 8.3mm） 工作温度:-40°C ~ 85°C 效率:94.8% 功率（W） - 最大值:88W 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。