- 您现在的位置：买卖IC网 > Datasheet目录538 > ZNBG4001Q16 (Diodes Inc)GENERATOR FIXED BIAS Datasheet资料下载
参数资料
| 型号： | ZNBG4001Q16 |
| 厂商： | Diodes Inc |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | GENERATOR FIXED BIAS |
| 标准包装： | 2,500 |
| 功能： | 偏压控制器 |
| RF 型： | LNBs，PMR |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 散装 |
| 其它名称： | Q1232319 |
ZNBG4000 ZNBG4001
ZNBG6000 ZNBG6001
TYPICAL APPLICATION CIRCUIT
APPLICATIONS INFORMATION
The above is a partial application circuit for the ZNBG series showing all external components
required for appropriate biasing. The bias circuits are unconditionally stable over the full
temperature range with the associated FETs and gate and drain capacitors in circuit.
Capacitors C D and C G ensure that residual power supply and substrate generator noise is not
allowed to affect other external circuits which may be sensitive to RF interference. They also
serve to suppress any potential RF feedthrough between stages via the ZNBG device. These
capacitors are required for all stages used. Values of 10nF and 4.7nF respectively are
recommended however this is design dependent and any value between 1nF and 100nF could
be used.
The capacitors C NB and C SUB are an integral part of the ZNBGs negative supply generator. The
negative bias voltage is generated on-chip using an internal oscillator. The required value of
capacitors C NB and C SUB is 47nF. This generator produces a low current supply of approximately
-3 volts. Although this generator is intended purely to bias the external FETs, it can be used to
power other external circuits via the C SUB pin.
Resistors R CAL1/2 sets the drain current at which all external FETs are operated. Both ZNBG devices
have the facility to program different drain currents into selected FETs. Two R CAL inputs are
provided. For the ZNBG4000, resistor R CAL1 sets the drain current of FETs 1 and 2, resistor R CAL2
sets the drain current of FETs 3 and 4. For the ZNBG6000, resistor R CAL1 sets the drain current
of FETs 1 and 4, resistor R CAL2 sets the drain current of FETs 2, 3, 5 and 6. If the same drain current
is required for all FETs on either device then pins R CAL1 and R CAL2 can be wired together and
shunted to ground by a single calibration resistor of half normal value.
If any bias control circuit is not required, its related drain and gate connections may be left open
circuit without affecting the operation of the remaining bias circuits. If all FETs associated with
a current setting resistor are omitted, the particular R CAL should still be included. The supply
current can be reduced, if required, by using a high value R CAL resistor (e.g. 470k).
4-142
相关PDF资料 |
PDF描述 |
|---|---|
| ZRC-8 | LED MOUNT CLIP LIGHT BAR STRIP |
| ZRS-8480-CW | LED COOL WHITE LIGHT BAR STRIP |
| ZS-26-C | PANEL MOUNT ADAPTER PSE200 |
| ZVN0124ASTZ | MOSFET N-CHAN 240V TO92-3 |
| ZVN0540ASTZ | MOSFET N-CHAN 400V TO92-3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZNBG4001Q16TC | 功能描述:接口 - 专用 4BIAS GENERATOR 2.0V RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| ZNBG4003 | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:4 STAGE FET LNA BIAS CONTROLLER |
| ZNBG4003JA16TC | 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:4 STAGE FET LNA BIAS CONTROLLER |
| ZNBG4115Q20TC | 制造商:Diodes Incorporated 功能描述:IC |
| ZNBG4210Q24 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
发布紧急采购，3分钟左右您将得到回复。