- 您现在的位置：买卖IC网 > PDF目录18734 > 0622022070 (Molex Inc)TOOL REMOVAL STIFFENER 4&5 PAIR PDF资料下载
参数资料
| 型号： | 0622022070 |
| 厂商： | Molex Inc |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | TOOL REMOVAL STIFFENER 4&5 PAIR |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062202-2070 62202-2070 622022070 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
GbX ? Backplane and Daughtercard Tooling
*GbX ? is a Trademark of Amphenol Corp.
4.2 Standard Tool Ordering Procedure
Stacking Tooling
All the insertion tooling listed in Table 4-1 and 4-2 can be stacked in any combination so as to be able to
simultaneously press in any arrangement of stacked connectors. Tooling holders are available in various lengths.
Figure 4-1 shows a typical setup for a 4 pair by 25 wide signal module and a one up power module in a standard
tool holder.
Ordering Tooling for Backplane Connectors
In order to insert a typical row of backplane connectors, it is necessary
to select the individual insertion tools and then pick the appropriate
tooling holder (See example).
Basic Procedure
1. Determine the combination of signal modules and power modules
to be inserted.
2. Select the proper insertion modules from Table 4-1 and Table 4-2.
3. Table 4-1 and Table 4-2 show the tool sizes. (L) Write down the
Figure 4-1
TYPICAL INSERTION
TOOL ASSEMBLY
length of each tool selected.
NOTE: Make sure that if you require four of a particular tool, write down its length 4 times.
NOTE: When using two 10 wide backplane insertion modules to press in a 20 wide header, only one module
uses a side plate with a locating peg. On the second module, replace the pegged side plate with 62202-2003
un-pegged version.
4. Total up these lengths.
5. Using the length just calculated, select the next largest tooling holder from Table 4-3. The tooling holder can be
shorter than the total tooling but not by more than 0.5 mm per side.
6. All of the tools selected above must be ordered separately.
Example
To be inserted: (1) 4 pair 25 wide Backplane Signal Module and (1) 4
pair 1 up Power Module.
1. Look at Table 4-1 and find the required tools. In this case it would
be a 62202-2020 and a 62202-2005.
2. From Table 4-1 get the lengths of these tools. (Numbers may be
rounded up) 62202-2020 =46.25mm and 62202-2005 = 5.55mm.
3. Add these two values for a total of 51.80mm.
4. From the Tooling Holder list in Table 4-3, pick the 72mm long
holder, P.N. 62201-9502.
5. Thus the order to Molex should include the following:
62201-9502
62202-0205
62202-2020
Figure 4-2
EXAMPLE TOOL ASSEMBLY
Doc. No: TM-622022099
Revision: H
Release Date: 06-23-04
Revision Date: 01-28-11
UNCONTROLLED COPY
Page 20 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| D2VW-01L1A-1MS | SWITCH BASIC SPDT .1A SEALED |
| GLCA01K8B | SWITCH WISKER HEAD SNAP ACT SPDT |
| EM260-RTY | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| DP1205C915 | MODULE DROP IN FOR XE1205 915MHZ |
| DP1205C868 | MODULE DROP IN FOR XE1205 868MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622022080 | 功能描述:TOOL RECPT SINGLE WAFER REMOVAL RoHS:是 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622022081 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022082 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022083 | 制造商:Molex 功能描述:Single Wafer Removal Tool For DaughterCard Receptacle 制造商:Molex 功能描述:CONN ACC REMOVAL TOOL - Bulk 制造商:Molex 功能描述:WAFER REMOVAL TOOL DAUGHTERCARD |
| 0622022086 | 功能描述:RAM CARD SGL WAFER REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。