- 您现在的位置：买卖IC网 > PDF目录18734 > 0622022070 (Molex Inc)TOOL REMOVAL STIFFENER 4&5 PAIR PDF资料下载
参数资料
| 型号： | 0622022070 |
| 厂商： | Molex Inc |
| 文件页数： | 24/28页 |
| 文件大小： | 0K |
| 描述： | TOOL REMOVAL STIFFENER 4&5 PAIR |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062202-2070 62202-2070 622022070 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
GbX ? Backplane and Daughtercard Tooling
*GbX ? is a Trademark of Amphenol Corp.
BACKPLANE SHIELDS
5.2
GbX ? Backplane Shield Repair Procedure:
For the removal and replacement of Backplane Shield.
The following tools are required:
Shield Removal Tool 62202-2100
5/16” T-handle wrench *
Plastic hammer *
Appropriate signal insertion module
(For shield replacement)
* Not supplied by Molex
The backplane shield removal tool will remove 10 to
CONNECTOR
RETENTION FORKS
OF THE SHIELD
REMOVAL TOOL
25 wide shields, from 2, 3, 4, and 5 pair assemblies.
NOTE: Never reuse a backplane shield once it has been removed.
MAKE SURE
THERE IS NOT DEBRIS
IN THIS AREA
Figure 5-4
Removal
Preset the shield removal tool so the retention grippers are fully extended and there is no debris in the area shown in
Figure 5-4. Insert the tip of the removal tool into the connector with the grippers over the shield to be removed. Be
careful not to damage the metallic parts in the connector. Insert a 5/16“ T-handle (not supplied with this tool) into the
socket head screw on the top of the tool, (See Figure 5-5) and rotate clockwise until the tool grips the shield. Then
continue to turn the T-handle one complete rotation. Remove the tool and shield by lifting vertically from the
connector. Remove the shield from the tool by rotating the socket head screw counter-clockwise three complete
turns.
Replacement
To install a replacement shield, use the appropriate signal insertion module for the connector being repaired. The
shields must be installed with the protruding stiffening ribs facing away from the backplane notch on the connector
housing. See Figure5-6. Preload the shield in its proper location and then load the insertion module. Gently tap the
top of the insertion module with the plastic hammer until the shield is fully seated.
NOTCHES IN
CONNECTOR HOUSING
5/16”T-HANDLE
WRENCH
(CUSTOMER SUPPLIED
62202-2100
SHIELD REMOVAL
TOOL
Figure 2
THE BACKPLANE
STIFFENER RIBS ARE
FACING AWAY FROM
THE NOTCH SIDE OF
THE CONNECTOR
Figure 5-6
Doc. No: TM-622022099
Revision: H
Release Date: 06-23-04
Revision Date: 01-28-11
UNCONTROLLED COPY
Page 24 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| D2VW-01L1A-1MS | SWITCH BASIC SPDT .1A SEALED |
| GLCA01K8B | SWITCH WISKER HEAD SNAP ACT SPDT |
| EM260-RTY | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| DP1205C915 | MODULE DROP IN FOR XE1205 915MHZ |
| DP1205C868 | MODULE DROP IN FOR XE1205 868MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622022080 | 功能描述:TOOL RECPT SINGLE WAFER REMOVAL RoHS:是 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622022081 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022082 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022083 | 制造商:Molex 功能描述:Single Wafer Removal Tool For DaughterCard Receptacle 制造商:Molex 功能描述:CONN ACC REMOVAL TOOL - Bulk 制造商:Molex 功能描述:WAFER REMOVAL TOOL DAUGHTERCARD |
| 0622022086 | 功能描述:RAM CARD SGL WAFER REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。