- 您现在的位置：买卖IC网 > PDF目录18734 > 0622022070 (Molex Inc)TOOL REMOVAL STIFFENER 4&5 PAIR PDF资料下载
参数资料
| 型号： | 0622022070 |
| 厂商： | Molex Inc |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | TOOL REMOVAL STIFFENER 4&5 PAIR |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062202-2070 62202-2070 622022070 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
GbX ? Backplane and Daughtercard Tooling
HOLDER
TYPICAL
INSERTION MODULES
Figure 2-3
MOUNTING INSERT MODULE IN A MOUNTING BLOCK
3. Now tighten the M3 set screws against the
modules with one (1) screw against each power
module inserter, two (2) screws evenly spaced on
*GbX ? is a Trademark of Amphenol Corp.
Figure 2-5
ALIGNING TERMINAL
PINS TO HOLES
2. Locate the pre-loaded board into the support
pallet. See Figure 2-6.
a 10 wide header insertion module and at least
three (3) screws evenly spaced on a 25 wide
header insertion module. Figure 2-4 shows a
LOCATING
PIN
PC BOARD
LOCATING PIN
typical completed assembly.
CAUTION: Do not over tighten the setscrews; this
could damage the insertion tool.
NOTE: See Section 4 for details on selecting
modules and mounting blocks.
CONNECTOR
ASSEMBLY
SUPPORT PALLET
Figure 2-6
CONNECTOR ASSEMBLY ON
PC BOARD SUPPORT PALLET
3. Locate the tooling assembly in the connector
assembly, carefully checking alignment. The
orientation feature on the tool must engage with
the notch on the connector body. See Figure 2-7.
Figure 2-4
TYPICAL INSERTION
TOOL ASSEMBLY
2.4
Operation
Header insertion Tooling
1. Carefully locate the connector(s) on the
printed circuit board and start in by hand.
Make sure terminal pin 1 is in the correct
position on all connectors. See Figure 2-5.
Figure 2-7
TOOLING LOCATED IN THE
CONNECTOR ASSEMBLY
Doc. No: TM-622022099
Revision: H
Release Date: 06-23-04
Revision Date: 01-28-11
UNCONTROLLED COPY
Page 8 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| D2VW-01L1A-1MS | SWITCH BASIC SPDT .1A SEALED |
| GLCA01K8B | SWITCH WISKER HEAD SNAP ACT SPDT |
| EM260-RTY | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| DP1205C915 | MODULE DROP IN FOR XE1205 915MHZ |
| DP1205C868 | MODULE DROP IN FOR XE1205 868MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622022080 | 功能描述:TOOL RECPT SINGLE WAFER REMOVAL RoHS:是 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622022081 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022082 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022083 | 制造商:Molex 功能描述:Single Wafer Removal Tool For DaughterCard Receptacle 制造商:Molex 功能描述:CONN ACC REMOVAL TOOL - Bulk 制造商:Molex 功能描述:WAFER REMOVAL TOOL DAUGHTERCARD |
| 0622022086 | 功能描述:RAM CARD SGL WAFER REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。