- 您现在的位置：买卖IC网 > PDF目录18734 > 0622022070 (Molex Inc)TOOL REMOVAL STIFFENER 4&5 PAIR PDF资料下载
参数资料
| 型号： | 0622022070 |
| 厂商： | Molex Inc |
| 文件页数： | 23/28页 |
| 文件大小： | 0K |
| 描述： | TOOL REMOVAL STIFFENER 4&5 PAIR |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062202-2070 62202-2070 622022070 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页
GbX ? Backplane and Daughtercard Tooling
*GbX ? is a Trademark of Amphenol Corp.
5.1
GbX ? Backplane Repair Procedure:
For the removal and replacement of Signal Pair pins.
The following tools are required:
Signal Pair Pin Replacement Tool 62202-2090
Shield Removal Tool 62202-2100
5/16” T-handle wrench *
Needle nose pliers (miniature) *
Tweezers *
Plastic hammer *
* Not supplied by Molex
Removal
To remove damaged signal pins, grasp them with the needle
nose pliers and pull straight up from the board. It is
recommended that both pins in a pair be replaced. See Figure
NEEDLE NOSE
PLIERS
CONNECTOR
SIGNAL PINS
FIGURE 5-1
5-1. In some cases it may be necessary to straighten a bent pin with the tweezers to allow access with the pliers.
NOTE: Never reuse a backplane signal pin once it has been removed. Also, no more than three pins should be
pressed into any plated through hole.
Replacement
To replace pairs of pins, use insertion tool no. 62202-2090.
Note: The pins are left and right handed and must be loaded into the connector in their proper orientation. They
should be positioned in the insertion tool so that the
ribs on the center of the pins are located in the
grooves in the tip of the tool, facing the round
indentations. Due to the small size of the pins, a
tweezers may help in this operation. There should be
a slight friction fit when the pins are inserted all the
way in to the tip. See Figure 5-2. Carefully load and
push the pins down into the connector base until the
tool stops against the board. See Figure 5-3. Then
remove the inserter from the connector.
INSERTION
TOOL
62202-2090
CONNECTOR
INSERTION
TOOL
62202-2090
RIB OF PIN
IN THE GROOVE
ROUND
SIGNAL PINS
OF TOOL
SIGNAL PINS
INDENTATIONS
Figure 5-2
Figure 5-3
Doc. No: TM-622022099
Revision: H
Release Date: 06-23-04
Revision Date: 01-28-11
UNCONTROLLED COPY
Page 23 of 28
相关PDF资料 |
PDF描述 |
|---|---|
| D2VW-01L1A-1MS | SWITCH BASIC SPDT .1A SEALED |
| GLCA01K8B | SWITCH WISKER HEAD SNAP ACT SPDT |
| EM260-RTY | IC ZIGBEE SYSTEM-ON-CHIP 40-QFN |
| DP1205C915 | MODULE DROP IN FOR XE1205 915MHZ |
| DP1205C868 | MODULE DROP IN FOR XE1205 868MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0622022080 | 功能描述:TOOL RECPT SINGLE WAFER REMOVAL RoHS:是 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0622022081 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022082 | 制造商:Molex 功能描述:JAW - Bulk |
| 0622022083 | 制造商:Molex 功能描述:Single Wafer Removal Tool For DaughterCard Receptacle 制造商:Molex 功能描述:CONN ACC REMOVAL TOOL - Bulk 制造商:Molex 功能描述:WAFER REMOVAL TOOL DAUGHTERCARD |
| 0622022086 | 功能描述:RAM CARD SGL WAFER REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。