- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213563-1 (TE Connectivity)TOOL DAHT ADAPTER ASSEMBLY Datasheet资料下载
参数资料
| 型号： | 1213563-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | TOOL DAHT ADAPTER ASSEMBLY |
| 标准包装： | 1 |
| 附件类型： | 压接适配器 |
| 适用于相关产品： | * |
| 配用： | 1-49935-0-ND - TOOL HEAD CRIMP 22-10AWG SOLIS 1-46673-0-ND - TOOL HEAD CRIMP 22-16AWG STRATO 1-47387-0-ND - TOOL HEAD CRIMP 16-14AWG PIDG |
i
DAHT Adapter Assembly 1213563-- 1
3. SET UP
3.1. Crimp Head Removal from Hand Tool
1. Remove the two retaining rings from one side of
the hand tool body and push the retaining pins,
along with the two remaining retaining rings,
through the opposite side of the tool body as
shown in Figure 2.
2. Slide the crimp head out of the tool body.
3.2. Crimp Head Installation onto Adapter
The adapter has two quick pins installed. The quick
pins will be used to secure the crimp head to the
adapter. Therefore, these quick pins must be
removed prior to installing the crimp head, then
proceed as follows:
1. Align the crimp head mounting holes with the
adapter quick pin holes as shown in Figure 1, then
insert the crimp head into adapter cavity.
2. Install the quick pins through the slotted holes in
the adapter and into the crimp head mounting
holes. See Figure 1.
NOTE If quick pins become difficult to install, it may be
necessary to jog the clevises to properly align the
holes.
408-- 4485
3.3. Adapter Installation and Removal
After the crimp head has been installed onto the
adapter, the adapter is ready for installation onto the
pneumatic tool. Refer to Customer Manual 409--5862
for instructions on removing a previously installed
cam and tool holder from the pneumatic tool.
DANGER Air pressure must be removed from the
pneumatic tool t while crimp head or tool holder
is detached.
DANGER DO NOT operate the pneumatic tool without the
proper adapter and crimp head installed.
1. If the adapter cam setscrew is not installed in
the adapter cam, thread the setscrew into the
adapter cam two to three turns.
2. Place the adapter cam (with setscrew) onto the
piston rod of the pneumatic tool as shown in Figure
3. The adapter cam should butt against the piston
rod face. If not, turn the setscrew counterclockwise
until the adapter cam fits on the piston rod
properly.
CAUTION Over--tightening the adapter cam setscrew may
damage the setscrew or cam.
!
DANGER
After the crimp head is installed, make sure that
the quick pins are FULLY inserted to avoid
personal injury and damage to the tool.
Retaining Pins
3. Using the hex wrench supplied with the adapter,
tighten the cam setscrew, then pull on the cam to
ensure that it is firmly attached.
Typical DAHT
Handle Assembly
Retaining Rings
Typical DAHT
Crimp Head
Retaining Rings
Figure 2
2 of 5
Tyco Electronics Corporation
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| 1213670-1 | TOOL SEATING ASSY FOR STACK RJ45 |
| 1213783-1 | TOOL HAND CRIMP 16-26AWG |
| 1213860-1 | CERTI-CRIMP II ADAPT-SDE BENCH |
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213564-1 | 功能描述:手工工具 ADAPTER RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1213565-1 | 制造商:TE Connectivity 功能描述:CLEVIS - Bulk |
| 1213566-1 | 制造商:TE Connectivity 功能描述:CLEVIS 制造商:TE Connectivity 功能描述:CLEVIS - Bulk |
| 1213573-1 | 制造商:TE Connectivity 功能描述:BLADE, GUIDE - Bulk |
| 1-213574-1 | 功能描述:管脚和插座连接器 BLADE SHEAR UPPER W/BDLK LF RoHS:否 制造商:Molex 系列:1561 产品类型:Contacts 触点类型:Socket (Female) 节距: 位置/触点数量: 排数: 安装风格:Wire 端接类型:Crimp 外壳材料: 触点材料:Brass 触点电镀:Tin 电压额定值: 电流额定值: |
发布紧急采购，3分钟左右您将得到回复。