- 您现在的位置：买卖IC网 > Datasheet目录591 > 1213563-1 (TE Connectivity)TOOL DAHT ADAPTER ASSEMBLY Datasheet资料下载
参数资料
| 型号： | 1213563-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL DAHT ADAPTER ASSEMBLY |
| 标准包装： | 1 |
| 附件类型： | 压接适配器 |
| 适用于相关产品： | * |
| 配用： | 1-49935-0-ND - TOOL HEAD CRIMP 22-10AWG SOLIS 1-46673-0-ND - TOOL HEAD CRIMP 22-16AWG STRATO 1-47387-0-ND - TOOL HEAD CRIMP 16-14AWG PIDG |
DAHT Adapter Assembly 1213563-- 1
Setscrew
Adapter
Cam
Pneumatic Tool
408-- 4485
Locking Ring
Adapter Assembly
Crimp Head
(Installed)
Piston
Rod
Friction
Ring
Stop Ring
Figure 3
i
4. Properly align the adapter with the cam and
push the adapter onto the pneumatic tool so that it
passes over the friction ring of the pneumatic tool.
5. Slide the locking ring toward the adapter until it
butts against the stop ring of the pneumatic tool.
Then turn the locking ring clockwise to engage
threads on the bottom of the adapter. Tighten the
locking ring to fully secure the adapter.
NOTE When the adapter is properly installed, the
locking ring should be butted against the stop
ring and threads of the adapter should not be
visible. If not properly installed, check that correct
combination of cam and adapter was used and
that they are aligned properly.
6. Rotate the adapter one full turn in each direction
and note that the locking ring rotates with the
adapter.
8. Removal is the reverse of installation.
4. MAINTENANCE AND INSPECTION
A maintenance and inspection program should be
performed periodically to ensure dependable and
uniform terminations.
DANGER To avoid personal injury, ALWAYS disconnect the
main air supply and electrical supply (if
applicable) of the pneumatic tool before
performing maintenance or inspection.
4.1. Daily Maintenance
Each operator must be responsible for the following
steps of daily maintenance:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a lint--free cloth. DO
NOT use objects that could damage the adapter.
DANGER
To avoid personal injury, periodically check that
the locking ring is tightly securing the adapter.
2. Make sure that all pins, rings, and other
components are in place and secure.
7. Connect the pneumatic tool to an adequate
air supply (between 620 and 690 kPa [90 and
100 psi]). For specific information on air line
requirements and air hose installation, refer to
409--5862.
3. Make certain all surfaces are protected with a
thin coat of any good SAE 20 motor oil. DO NOT
oil excessively.
4. When the adapter assembly is not in use, store
it in a clean, dry area.
SAE is a trademark of SAE International Corporation.
Rev B
Tyco Electronics Corporation
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 1213670-1 | TOOL SEATING ASSY FOR STACK RJ45 |
| 1213783-1 | TOOL HAND CRIMP 16-26AWG |
| 1213860-1 | CERTI-CRIMP II ADAPT-SDE BENCH |
| 1214518-2 | TOOL EXTRACTION FOR AMPLIVAR |
| 1214695-1 | TOOL CRIMPER ASSY BACKSHELL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 1213564-1 | 功能描述:手工工具 ADAPTER RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1213565-1 | 制造商:TE Connectivity 功能描述:CLEVIS - Bulk |
| 1213566-1 | 制造商:TE Connectivity 功能描述:CLEVIS 制造商:TE Connectivity 功能描述:CLEVIS - Bulk |
| 1213573-1 | 制造商:TE Connectivity 功能描述:BLADE, GUIDE - Bulk |
| 1-213574-1 | 功能描述:管脚和插座连接器 BLADE SHEAR UPPER W/BDLK LF RoHS:否 制造商:Molex 系列:1561 产品类型:Contacts 触点类型:Socket (Female) 节距: 位置/触点数量: 排数: 安装风格:Wire 端接类型:Crimp 外壳材料: 触点材料:Brass 触点电镀:Tin 电压额定值: 电流额定值: |
发布紧急采购，3分钟左右您将得到回复。