- 您现在的位置：买卖IC网 > Datasheet目录593 > 1320369-1 (TE Connectivity)TOOL CRIMPING HEAD 8AWG COPALUM Datasheet资料下载
参数资料
| 型号： | 1320369-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/10页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPING HEAD 8AWG COPALUM |
| 标准包装： | 1 |
| 压接或电缆尺寸： | 8 AWG |
| 压接手柄： | 189721-2，189722-2 |
| 连接器类型： | 端子及连接件 |
i
Pneumatic Crimping Heads 662546- 1 and 1320369- 1
5. Refer to Section 6 for crimp inspection.
5.2. Butt Splice Crimping Procedure
1. Open crimping jaws by squeezing rollers
together simultaneously; then position the butt
splice in the crimping chamber on the lower jaw, as
shown in Figure 3, Detail B. The butt splice is
properly positioned when the window in the splice
is facing the upper jaw and the splice wire stop is
sitting on the locator.
2. After splice is properly positioned, release rollers
to allow crimping jaws to spring shut, holding splice
in place.
3. Insert stripped wire into splice wire barrel until
the end of the conductor butts against the splice
wire stop.
4. Activate the tool to complete the crimp. Open
crimping jaws by squeezing the rollers together
simultaneously; then remove crimped splice.
5. To crimp the other half of the splice, follow the
same procedure for the uncrimped half of the
splice.
Detail A — Terminal
408- 4366
NOTE A slight bend in the splice may result from
crimping the other half of the splice as instructed
in Step 1. If a bend would be objectionable,
position the other half of the splice in the
crimping chamber by rotating the splice 180 _
end--over--end; then crimp.
6. Refer to Section 6 for crimp inspection.
5.3. Parallel Splice Crimping Procedure
1. Open crimping jaws by squeezing rollers
together simultaneously; then position the parallel
splice in the crimping chamber on the lower jaw, as
shown in Figure 3, Detail C. The parallel splice is
properly positioned when the end of the splice is
against the locator.
2. After splice is properly positioned, release rollers
to allow crimping jaws to spring shut, holding splice
in place.
3. Insert stripped wires into splice until the end of
the conductors butt against the locator.
4. Activate the tool to complete the crimp. Open
crimping jaws by squeezing the rollers together
simultaneously; then remove crimped splice.
5. Refer to Section 6 for crimp inspection.
Detail B — Butt Splice
Splice Window
Facing Upper Jaw
Wire Barrel
Against Locator
Splice Wire Stop
Sitting on Locator
End of Conductor
Against Locator
Lower
Jaw
Back of Terminal
Facing Upper Jaw
Lower
Jaw
End of Conductor
Against Splice Wire Stop
Detail C — Parallel Splice
End of Conductors
Against Locator
End of Splice
Against Locator
Lower
Jaw
Figure 3
Rev C
Tyco Electronics Corporation
3 of 10
相关PDF资料 |
PDF描述 |
|---|---|
| 1320447-1 | TOOL DIE ASSY 2AWG BREAKAWAY |
| 1338273-1 | TOOL DIE ASSY 22-16AWG SOLIS |
| 1366402-1 | TOOL HAND 18-22AWG STR ACTION |
| 1366865-1 | EXT-TOOL FOR 025 TAB CONTACT |
| 1372039-1 | TOOL HAND MONO SHAPE MK II |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 132036-HMC858LC4B | 制造商:Hittite Microwave Corp 功能描述:BOARD EVAL FOR HMC858LC4B |
| 132038 | 制造商:Brady Corporation 功能描述:B302 POLYESTER BLK,RED/WHT 10X14 |
| 1320383-1 | 功能描述:手工工具 BODY, TUBE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 1320384-1 | 功能描述:手工工具 TUBE BOTTOM RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 132039 | 制造商:Brady Corporation 功能描述:B120 FIBERGLASS BLK,RED/WHT 7X10 |
发布紧急采购，3分钟左右您将得到回复。