- 您现在的位置：买卖IC网 > PDF目录18660 > 2534 (3M)TOOL CLEAVER FIBER OPTIC PDF资料下载
参数资料
| 型号： | 2534 |
| 厂商： | 3M |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CLEAVER FIBER OPTIC |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 光纤切割器 |
| 其它名称： | 0-00-51115-30001-1 00051115258022 00051115300011 5111530001 51115300011 80-6113-2377-7 80611323777 |
3.0 Tools and Materials required
1) 3M Fibrlok II Splice Holder 2539
2) Buffer Stripper
3) Scissors (Snips)
4.0 Splicing Set-Up
4) Reagent Grade Isopropyl Alcohol
5) Lint-free Wipes
6) Cleaver
4.1
4.2
The splicing area should be clean, dry and well lit. A
clean, well organized splicing area will improve splice
efficiency and minimize the risk of contamination of
fibers or splices.
Open buffer tubes, expose and clean the fibers per your
company practice.
4.3 Remove the Fibrlok II Splice/Holder from its
protective package.
4.4 Secure the Fibrlok II Splice/Holder 2539
Before proceeding, attach the splice/holder to its final location. If there is not enough space to work, then
attach the splice/holder after completing the splice. Clean surface of dirt and debris with alcohol and a
lint-free cloth. To attach, remove the 3M VHB ? (Very High Bond) Tape release liner (red) and press
the splice/holder base firmly for several seconds onto the surface of its final location.
Note: VHB Tape is not re-positionable.
4.5 Lift the buffer clamps at both ends of the
splice/holder and lift the actuation lever to the “up”
position
5.0 Fiber Preparation
Note: The 3M Fibrlok II Splice/Holder is designed for 900 μ m tight buffer and 250 μ m primary coated
fiber. To splice 900 μ m loose tube, semi-tight, or release layered fiber remove the 900 μ m coating within the
last four inches or more from the fiber end to be cleaved.
5.1 Remove the minimum length of the cable outer jacket
needed to prepare and splice fibers.
5.2 Strip 1.5 to 1.75 inches (38mm to 45mm) of plastic coating
from the fiber using a clean mechanical stripper.
5.3 Clean the bare glass by pulling the fiber through an alcohol
soaked lint-free wipe.
Note: Do not wipe the fibers more than two times, and limit the time that the bare fiber is exposed to the
atmosphere.
5.3 Cleave the fiber to 12.5mm +/- 0.5mm (0.49+/0.02 inches) for both 250 μ m and 900 μ m tight buffer
coated fibers.
Note: Do not clean fibers again after they have been cleaved or allow cleaved ends to contact tools.
相关PDF资料 |
PDF描述 |
|---|---|
| XMLEZW-00-0000-0D0PT227F | LED XLAMP XML EASYWHITE 12V SMD |
| XMLEZW-00-0000-0D0HT640F | LED XLAMP XML EASYWHITE 12V SMD |
| IXFX40N90P | MOSFET N-CH PLUS247 |
| XMLEZW-00-0000-0D0HT535F | LED XLAMP XML EASYWHITE 12V SMD |
| MICA-KIT6F | KIT MICA 2.0PF - 1500PF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25340 | 制造商:Greenlee Textron Inc 功能描述:Conduit And Pipe Capacity Mild Steel 10 GA 制造商:Greenlee Textron Inc 功能描述:CONDUIT AND PIPE |
| 2534-00H | 功能描述:固定电感器 100uH 3% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00H BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 3% |
| 2534-00J | 功能描述:固定电感器 100uH 5% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00J BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 5% |
发布紧急采购，3分钟左右您将得到回复。