- 您现在的位置：买卖IC网 > PDF目录18660 > 2534 (3M)TOOL CLEAVER FIBER OPTIC PDF资料下载
参数资料
| 型号： | 2534 |
| 厂商： | 3M |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CLEAVER FIBER OPTIC |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 光纤切割器 |
| 其它名称： | 0-00-51115-30001-1 00051115258022 00051115300011 5111530001 51115300011 80-6113-2377-7 80611323777 |
7.8 Grasp the left fiber about 2 inches from the holder and push the
fiber in until it bows about 1/8 to 1/4 inch (3mm to 6mm). Push
down on the actuation lever until the Fibrlok II Splice is actuated.
An audible click can be heard and you should feel the splice cap
snap down into place when completely closed. The cap should be
level with the Fibrlok splice top surface.
7.9 Release the bow in the fiber and fully close the left buffer clamp.
Again, you will hear an audible snap.
8.0 Fiber Repositioning
8.1 If high loss is observed after the splice has been actuated, it is possible that the fiber ends are separated.
In this case, lift the splice cap and reposition the fiber ends, as instructed below.
8.2 While the splice is still in the holder assembly, lift the actuation
lever and insert the cap removal tool over the splice cap. Grasp
both sides of the splice holder base and lift the cap up and off the
splice while gently rocking lengthwise. Replace the cap parallel
to the top, but raised about 1mm (0.04 inch) as it snaps into
place.
8.3 Carefully reposition fiber. Refer to section 7.0 for proper
fiber centering and splice actuation.
8.4 Place splice cap back on the Fibrlok splice and push down the
actuation lever until cap has been fully actuated.
8.5 If after two attempts, an acceptable splice loss is not obtained,
remove fibers and replace the Fibrlok splice with a new splice.
Redo fiber preparation (section 5) by re-stripping, cleaning, and
cleaving both fibers. Then repeat steps in section 7.
8.6 Upon completion, the actuation lever can be removed and
discarded if desired.
Rev B
相关PDF资料 |
PDF描述 |
|---|---|
| XMLEZW-00-0000-0D0PT227F | LED XLAMP XML EASYWHITE 12V SMD |
| XMLEZW-00-0000-0D0HT640F | LED XLAMP XML EASYWHITE 12V SMD |
| IXFX40N90P | MOSFET N-CH PLUS247 |
| XMLEZW-00-0000-0D0HT535F | LED XLAMP XML EASYWHITE 12V SMD |
| MICA-KIT6F | KIT MICA 2.0PF - 1500PF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25340 | 制造商:Greenlee Textron Inc 功能描述:Conduit And Pipe Capacity Mild Steel 10 GA 制造商:Greenlee Textron Inc 功能描述:CONDUIT AND PIPE |
| 2534-00H | 功能描述:固定电感器 100uH 3% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00H BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 3% |
| 2534-00J | 功能描述:固定电感器 100uH 5% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00J BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 5% |
发布紧急采购，3分钟左右您将得到回复。