- 您现在的位置：买卖IC网 > PDF目录18660 > 2534 (3M)TOOL CLEAVER FIBER OPTIC PDF资料下载
参数资料
| 型号： | 2534 |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CLEAVER FIBER OPTIC |
| 标准包装： | 1 |
| 系列： | Fibrlok™ |
| 类型： | 光纤切割器 |
| 其它名称： | 0-00-51115-30001-1 00051115258022 00051115300011 5111530001 51115300011 80-6113-2377-7 80611323777 |
Note: Cleavers must be in good operating condition and used per the manufacturer’s instructions. They
should provide consistent cleave-to-coating lengths within +/- 0.5mm. Acceptable cleavers will produce
cleaved ends within 0.5° of perpendicular (typical always <1 °), free from major defects.
5.5 Cleave lengths can be confirmed on the 12.5mm length
gauge. Cleave should be within the window.
6.0 3M Fibrlok II Splice/Holder Pigtail Assembly
2539 SC/APC and 2539 SC/UPC
6.1 Cut off rubber band, position actuation lever over splice, and
lift both buffer clamps to the “up”position.
6.2 Confirm that buffer on pigtail is fully inserted inside
splice and follow steps 7.2 through 7.9.
7.0 Splice/Holder Assembly 2539
Note: Always insert the fiber first on the right (actuation lever
side) of the splice/holder.
7.1 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert cleaved fiber into the guide on the right
(actuation lever side) of the splice/holder until it stops inside
the Fibrlok II splice.
Note: Push fiber straight into the fiber alignment guide, not at
an angle. Bare glass should not be visible outside of the splice. If
bare glass is visible, pull back slightly on the fiber and continue
insertion until resistance is met. Do not fully remove fibers from
splice after initial insertion.
7.2 Carefully mark the buffer at the right edge of the base.
7.3 Prepare second fiber (strip, clean and cleave) as described in
section 5.
7.4 Holding the fiber approximately ? inch (13mm) from the
bare glass, insert second fiber into the guide on the left side
(opposite actuation lever) of the splice/holder until it stops
inside the Fibrlok II splice.
7.5 While sliding the second fiber into the splice, the mark on the
first fiber should move outwards 1/8 inch (3mm) showing the
fiber ends are in contact. If this is not observed, one or both
fibers has a bad/short cleave. Remove one fiber and re-strip,
clean, re-cleave and insert back into the splice. If contact is
still not correct, repeat procedure for second fiber.
Note: To prevent contamination, never fully remove and re-
insert a cleaved end back into a splice without first re-stripping
and re-cleaving.
7.6 Center both fiber cleaves by repositioning the mark on the first
fiber half way back to its original position.
7.7 Once the fibers are centered, fully close the right buffer clamp.
You will hear an audible snap.
相关PDF资料 |
PDF描述 |
|---|---|
| XMLEZW-00-0000-0D0PT227F | LED XLAMP XML EASYWHITE 12V SMD |
| XMLEZW-00-0000-0D0HT640F | LED XLAMP XML EASYWHITE 12V SMD |
| IXFX40N90P | MOSFET N-CH PLUS247 |
| XMLEZW-00-0000-0D0HT535F | LED XLAMP XML EASYWHITE 12V SMD |
| MICA-KIT6F | KIT MICA 2.0PF - 1500PF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 25340 | 制造商:Greenlee Textron Inc 功能描述:Conduit And Pipe Capacity Mild Steel 10 GA 制造商:Greenlee Textron Inc 功能描述:CONDUIT AND PIPE |
| 2534-00H | 功能描述:固定电感器 100uH 3% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00H BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 3% |
| 2534-00J | 功能描述:固定电感器 100uH 5% 1.5ohm Molded Unshield Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 2534-00J BULK 50 | 制造商:API Delevan 功能描述:INDUCTOR UNSHIELDED RF 100 UH 5% |
发布紧急采购，3分钟左右您将得到回复。