- 您现在的位置：买卖IC网 > Datasheet目录596 > 312253-2 (TE Connectivity)CONN SMA DIE/SET 50OHM RG402 2PC Datasheet资料下载
参数资料
| 型号： | 312253-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | CONN SMA DIE/SET 50OHM RG402 2PC |
| 标准包装： | 1 |
| 压接或电缆尺寸： | RG/U-402 |
| 压接手柄： | A9966-ND |
| 连接器类型： | SMA |
| 产品目录页面： | 453 (CN2011-ZH PDF) |
| 配用： | 413249-1-ND - CONTACT JACK COAX 405SR 413242-1-ND - CONTACT PLUG BLIND MATE STR GOLD |
| 相关产品： | A9966-ND - TOOL SMA CRIMP FRAME ONLY |
| 其它名称： | A9964 |
408-6788
Tool Setup
Detail A
Chamfer
Die-Holding Hex Head
Screws (Captive)
Chamfer
Detail B
Slip Cable in Locator
Between Dies. Tighten
Screws While Cable Holds
Dies in Proper Alignment
Locator
(Typ)
Locator Locking
Screw (Ref)
Figure 7
2. Place the connector and cable inside the tool
locator, making sure that:
— the center conductor of center contact enters the
locator hole
— the connector is seated squarely on the locator
— if crimping a panel jack to the cable, the sides of
the panel jack should align with the tool jaws as
shown in Figure 9
3. Support the cable-and-connector assembly, and
squeeze the tool handles to complete the crimp as
shown in Figure 9.
6.2. For Connectors with Retractable Collars
Connectors with sliding coupling nuts (shown in Figure
10) require Special Die Set 312962-1 which is not
included in the kit and MUST be ordered separately.
Proceed as follows:
1. Slide the nut then the connector body, flange end
first, onto the cable.
2. Place the connector body and cable inside the
tool locator, making sure that the center conductor
enters the locator hole, and that the coupling nut is
positioned above the tool head.
Crimping Connectors with Fixed Collars
(Except Right-Angle Connectors)
Center Conductor
of Connector Must
Enter Hole in
Locator
Rev L
Connector with
Fixed Collar
Figure 8
Dies will Close Against
Cable and Connector to
Complete Termination
6 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 318837-1 | EXTRACTION TOOL .093 CONN |
| 3430-1000 | DISCRETE WIRE INSERTION TOOL |
| 3430-2000 | DISCRETE WIRE HAND TOOL |
| 3430-4000 | HEADER ROLL PIN INSERTER |
| 350-MX23-2 | TOOL CRIMP FOR MX23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 31226103 | 制造商:METZ CONNECT USA 功能描述: |
| 31226106 | 制造商:METZ CONNECT USA 功能描述: |
| 31226108 | 制造商:METZ CONNECT USA 功能描述: |
| 31226110 | 制造商:METZ CONNECT USA 功能描述: |
| 31-2264 | 制造商:AMPHENOL 制造商全称:AMPHENOL 功能描述:TNC Jacks |
发布紧急采购，3分钟左右您将得到回复。