- 您现在的位置：买卖IC网 > PDF目录21904 > 4320-DKDB4 (Silicon Laboratories Inc)KIT DEV TEST EZRADIO SI4320 RX PDF资料下载
参数资料
| 型号： | 4320-DKDB4 |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | KIT DEV TEST EZRADIO SI4320 RX |
| 标准包装： | 1 |
| 附件类型： | 测试卡，接收器，915MHz |
| 适用于相关产品： | EZRadio? |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Si4320
In automatic operation mode (no strobe signal is needed from the microcontroller to update the output offset register), the AFC circuit is
automatically enabled when VDI indicates a potential incoming signal during the whole measurement cycle and the circuit measures the
same result in two subsequent cycles.
There are three operation modes, example from the possible application:
1, ( a1 =0, a0 =1) The circuit measures the frequency offset only once after power up. This way, the extended TX/RX maximum distance can
be achieved. Possible usage: In the final application when the user is inserted the battery the circuit measures and compensate the
frequency offset caused by the crystal tolerances. This method enables to use cheaper quartz in the application and provide quite good
protection against locking in an interferer.
2a, ( a1 =1, a0 =0) The circuit measures automatically the frequency offset during an initial low data rate pattern –easier to receive- (i.e.:
00110011) of the package and change the receiving frequency according that. The further part of the package can be received by the
corrected frequency settings.
2b, ( a1 =1, a0 =0) The transmitter must transmit the first part of the packet with a step higher deviation and later there is a possibility to
reduce it.
In both cases ( 2a and 2b ) when the VDI indicates poor receiving conditions (VDI goes low) the output register is automatically cleared. It’s
suggested to use when one receiver receives signal from more than one transmitter.
3, (a1=1, a0=1) It is similar to the 2a and 2b modes, but 3 is suggested to use when a receiver operates with only one transmitter. After a
complete measuring cycle, the measured value is held independently of the sate of VDI signal.
8. Data Filter Command
bit
15
1
14
1
13
0
12
0
11
0
10
1
9
0
8
0
7
al
6
ml
5
1
4
s1
3
s0
2
f2
1
f1
0
f0
POR
C42Ch
Bit 7 <al>:
Bit 6 <ml>:
Bit 3-4 <s0 : s1>:
Clock recovery (CR) auto lock control if set.
It means that the CR start in fast mode after locking it automatically switches to slow mode.
Clock recovery lock control
1: fast mode, fast attack and fast release
0: slow mode, slow attack and slow release
Using the slower one requires more accurate bit timing (see Data Rate Command).
Select the type of the data filter:
s1
0
0
1
1
s0
0
1
0
1
Filter Type
OOK to filter
Digital filter
Reserved
Analog RC filter
OOK to filter: the analog RSSI signal is used as received data. The DRSSI threshold level is used for slicing.
Digital: this is a digital realization of an analog RC filter followed by a comparator with hysteresis. The time constant is automatically
adjusted to the bit rate defined by the Data Rate Command.
Analog RC filter: The demodulator output is fed to pin 7 over a 10 kOhm resistor. The filter cut-off frequency is set by the external capacitor
connected to this pin and VSS.
The table shows the optimal filter capacitor values for different data rates:
1.2 kbps
12 nF
2.4 kbps
8.2 nF
4.8 kbps
6.8 nF
9.6 kbps
3.3 nF
19.2 kbps
1.5 nF
38.4 kbps
680 pF
57.6 kbps
270 pF
115.2 kbps
150 pF
256 kbps
100 pF
Note:
If analog RC filter is selected the internal clock recovery circuit and the FIFO cannot be used.
Bit 0-2 <f0 : f2>:
DQD threshold parameter.
Note:
To let the DQD report "good signal quality" the threshold parameter should be less than 4 in the case when the bitrate is close to
the deviation. At higher deviation/bitrate settings higher threshold parameter can report "good signal quality" as well.
16
相关PDF资料 |
PDF描述 |
|---|---|
| PSL0101WBFD1 | LED WHITE 90LM 350MA 3000K SSML |
| PSL0101WBFB1 | LED WHITE 80LM 350MA 3000K SSML |
| V600-IDSC02 | V600 CTRL 2 CH |
| PSL0102WBEC1 | LED WHITE 30LM 120MA 5000K SSML |
| PSL0102WBEB1 | LED WHITE 38LM 120MA 5000K SSML |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4320-DKDB5 | 功能描述:射频开发工具 Test Board BIFA Rx (868MHz) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4320-DKDB8 | 功能描述:射频开发工具 Test Board xloop Rx (915MHz) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4320-DKDB9 | 功能描述:射频开发工具 Test Board xloop Rx (868Mhz) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4320-L15 | 制造商:American Denki 功能描述: |
| 4320-P | 制造商:American Denki 功能描述: |
发布紧急采购，3分钟左右您将得到回复。