- 您现在的位置：买卖IC网 > Datasheet目录600 > 543518-1 (TE Connectivity)TOOL COVER TERMINATOR IDC AMPMOD Datasheet资料下载
参数资料
| 型号： | 543518-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 17/20页 |
| 文件大小： | 0K |
| 描述： | TOOL COVER TERMINATOR IDC AMPMOD |
| 标准包装： | 1 |
| 系列： | AMPMODU 50/50 栅格 |
| 压接手柄： | 91295-1 |
| 连接器类型： | 矩形 |
| 配用： | 5-104892-7-ND - CONN RECPT 70POS .050 W/ LATCH 5-104892-5-ND - CONN RECPT 50POS .050 W/ LATCH 5-104892-4-ND - CONN RECPT 40POS .050 W/ LATCH 5-104892-3-ND - CONN RECPT 30POS .050 W/ LATCH 5-104892-2-ND - CONN RECPT 20POS .050 W/ LATCH 6-104893-0-ND - CONN RECEPT 100POS .050 GOLD 5-104893-8-ND - CONN RECEPT 80POS .050 GOLD 5-104893-7-ND - CONN RECEPT 70POS .050 GOLD 5-104893-6-ND - CONN RECEPT 60POS .050 GOLD 5-104893-5-ND - CONN RECEPT 50POS .050 GOLD 更多... |
114- 7010
B. Internal Inspection (Figure 18)
1. Carefully remove both covers and check that each conductor is terminated.
2. Make sure that all contacts have penetrated the cable and that none are bent or deformed.
3. Make sure the conductors and contacts are placed in accordance with requirements provided.
Internal Inspection
Each Contact Must
be Aligned With a
Single Conductor
All Contacts Must
Penetrate Cable
Contacts Must Not be Bent After
Termination and Must Fit Within
the Termination Cover Slots
Cover Must Fully
Seat on Housing at
Cover End
Remove Wire From Slot
(Conductor Must be Exposed and
Deformed on Both Sides to be
Considered a Good Termination)
0.76 [.030] Min.
Wire Protrusion
Insulation Must be Intact,
Except in Area of Slot
(Tooling Marks on Wire
Insulation are Acceptable)
3.13. Mating and Unmating
Figure 18
Strand Closest to Transition Must
be a Minimum of One Full Strand
Diameter, to a Maximum of Three
Full Strand Diameters from the
Transition
Contact Base Metal Must
Not be Exposed or Deformed
During Termination
CAUTION
!
The use of uneven or off--angle forces during mating and unmating of the connectors could cause over--stress and
damage to the contacts and/or housings. Do NOT use the “peel--back” method of unmating one end and pulling it until
the other end is unmated. Also, do NOT use a severe side--to--side rocking motion to unmate connectors.
Connectors must be pushed straight in when mating and pulled straight out when unmating. A slight
side--to--side motion may be used to start extraction, but it must not continue through full extraction cycle.
Miniaturization is a design feature of these connectors and the systems in which they are used. Component
density, connector location, and pc board size may make it difficult to hold one connector in place while
extracting the other. Two methods are recommended to facilitate removal. The preferred method is to have one
of the pc boards securely fastened and adequately supported to withstand the pulling force applied to the other
pc board. The second method is to construct a tool for your system design that will produce a straight--away
separation of the connectors.
4. QUALIFICATIONS
The AMPMODU 50/50 Grid SMT and IDC Connectors are Listed by the following agencies.
4.1. Underwriters Laboratories Inc. (UL)
The connectors are Listed in UL File Number E28476.
4.2. Canadian Standards Association (CSA)
The connectors are Certified in File Number LR 7189--A00255.
Rev F
17 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| 55050C | XFRMR CURR SENSE 15A 1:1:50 SMD |
| 5510 | ADT KIT BNC-BAN PLUG & BIND POST |
| 5511/POM | KIT BNC COUPLER AND TEE |
| 5512 | ADAPTER KIT W/BNC MALE TERM |
| 5513 | KIT ATTENUATOR BNC 50 OHM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5435187 | 功能描述:固定接线端子 BCP-381F- 9 RoHS:否 制造商:Phoenix Contact 产品:Fixed Terminal Blocks 类型:Wire to Board 节距:5.08 mm 位置/触点数量:2 线规量程:26-16 电流额定值:13.5 A 电压额定值:250 V 安装风格:Through Hole 安装角:Straight 端接类型:Screw 触点电镀: |
| 5435190 | 功能描述:固定接线端子 BCP-381F-10 RoHS:否 制造商:Phoenix Contact 产品:Fixed Terminal Blocks 类型:Wire to Board 节距:5.08 mm 位置/触点数量:2 线规量程:26-16 电流额定值:13.5 A 电压额定值:250 V 安装风格:Through Hole 安装角:Straight 端接类型:Screw 触点电镀: |
| 5435192 | 制造商:Amphenol Aerospace 功能描述:Heavy Duty Cylindrical Connectors 制造商:Amphenol Corporation 功能描述:10-194632-05S - Bulk |
| 54-352 | 制造商:NTE Electronics 功能描述:SWITCH, TOGGLE, SPDT, 15A, 250V; Contact Configuration:SPDT; Switch Operation:(On)-Off-(On); Contact Voltage AC Nom:250V; Contact Voltage DC Nom:25V; Contact Current Max:15A; Switch Terminals:Quick Connect, Solder; Actuator Style:Bat;RoHS Compliant: Yes 制造商:NTE Electronics 功能描述:Switch Toggle (ON) OFF (ON) SPDT Bat Toggle Quick Conn/Solder Lug 15A 250VAC 25VDC Panel Mount with Threads |
| 5435200 | 功能描述:固定接线端子 BCP-381F-11 RoHS:否 制造商:Phoenix Contact 产品:Fixed Terminal Blocks 类型:Wire to Board 节距:5.08 mm 位置/触点数量:2 线规量程:26-16 电流额定值:13.5 A 电压额定值:250 V 安装风格:Through Hole 安装角:Straight 端接类型:Screw 触点电镀: |
发布紧急采购，3分钟左右您将得到回复。