- 您现在的位置：买卖IC网 > Datasheet目录601 > 58560-1 (TE Connectivity)TOOL CRIMP MODULAR 10 POS W/DIE Datasheet资料下载
参数资料
| 型号： | 58560-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP MODULAR 10 POS W/DIE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 模块 - RJ50（10p10c） |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 303 (CN2011-ZH PDF) |
| 配用： | 5-406938-2-ND - CONN MOD PLUG 10-10 ROUND STRAND A106449-ND - MOD PLG ASSY/10POS/RND CBL 500PC A9129-ND - CONN MOD PLUG 10-10 ROUND STRAND |
| 其它名称： | A9798 |
Figure 3
Inspect connector for proper crimp height using an
indicator with needle–point probes. Refer to Figure 3
for correct crimp height measurement. If necessary,
adjust the crimp height as described in Section 6,
CRIMP HEIGHT ADJUSTMENT.
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the opposite side of the tool.
3. Observe the ratchet adjustment wheel; if a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate adjustment wheel CLOCKWISE to
a lower–numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, secure the
lockscrew. If the dimension is unacceptable,
continue to adjust the ratchet, and again measure
a sample crimp.
If correct crimp height cannot be obtained, tool and or
dies must be replaced See Section 8, PARTS
REPLACEMENT.
Tyco Electronics recommends that operators of the
tool be made aware of, and responsible for, the
following steps of daily maintenance:
1. Remove dust, moisture, and any other
contaminants from the tool with a clean, soft brush,
or a clean, soft, lint–free cloth. Do NOT use hard or
abrasive objects that could damage the tool.
Figure 4
相关PDF资料 |
PDF描述 |
|---|---|
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58560-2 | 功能描述:冲压机与冲模 10 POS MOD PLUG PRO-CRIMP DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5856-1 WH005 | 制造商:Alpha Electronics Corporation 功能描述:EQUIPMENT WIRE 20AWG WHT |
| 58561 | 制造商:Alpha Wire Company 功能描述:WIRE UL1213 20 AWG WHITE 30.5M |
| 5856-10 VI005 | 制造商:Alpha Electronics Corporation 功能描述:EQUIPMENT WIRE 20AWG PUR |
| 585610 | 制造商:Alpha Wire Company 功能描述:WIRE UL1213 20 AWG VIOLET 30.5M |
发布紧急采购，3分钟左右您将得到回复。