- 您现在的位置：买卖IC网 > Datasheet目录601 > 58560-1 (TE Connectivity)TOOL CRIMP MODULAR 10 POS W/DIE Datasheet资料下载
参数资料
| 型号： | 58560-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP MODULAR 10 POS W/DIE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 模块 - RJ50（10p10c） |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 303 (CN2011-ZH PDF) |
| 配用： | 5-406938-2-ND - CONN MOD PLUG 10-10 ROUND STRAND A106449-ND - MOD PLG ASSY/10POS/RND CBL 500PC A9129-ND - CONN MOD PLUG 10-10 ROUND STRAND |
| 其它名称： | A9798 |
2. Make certain that the retaining pins are in place
and that they are secured with retaining rings.
3. All pins, pivot points, and bearing surfaces
should be protected with a thin coat of any good
SAE 20 motor oil. Do not oil excessively.
4. When the tool is not in use, keep handles closed
to prevent objects from becoming lodged in the
crimping jaws. Store the tool in a clean, dry area.
Regular inspection of the tool should be performed by
quality control personnel. A record of scheduled
inspections should remain with the tool or be supplied
to supervisor personnel responsible for the tool.
Inspection frequency should be based upon amount
of use, working conditions, operator training and skill,
and established company standards.
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 8, PARTS REPLACEMENT.
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) in a
suitable commercial degreaser that will not affect
paint or plastic material.
2. Make certain that all retaining pins are in place
and secured with retaining rings.
3. Close tool handles until ratchet releases and
then allow them to open freely. If they do not open
quickly and fully, the spring is defective and must
be replaced. See Section 8, PARTS AND
REPLACEMENT.
4. Inspect the tool frame for wear or damage,
paying particular attention to the tool jaws and
pivot points. If damage is evident, refer to Section
8, PARTS REPLACEMENT. If tool is acceptable,
lubricate and return to service.
5. Check the crimping dies occasionally to make
sure dies are not broken or chipped. If damage is
evident, refer to Section 8, PARTS
REPLACEMENT.
Customer–replaceable parts are shown in Figure 1.
Available separately, PRO–CRIMPER III Hand Tool
Repair Kit 679221–1 includes a replacement nut and
a variety of pins, rings, screws, and springs. If the
dies are damaged or worn excessively, they must be
replaced. Order the repair kit and replaceable parts
through your Tyco Electronics representative, or call
1–800–526–5142, or send a facsimile of your
purchase order to 1–717–986–7605, or write to:
CUSTOMER SERVICE (038–035)
TYCO ELECTRONICS CORPORATION
P.O. BOX 3608
HARRISBURG, PA 17105–3608
Since the previous release of this document, the TE
logo was changed.
相关PDF资料 |
PDF描述 |
|---|---|
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58560-2 | 功能描述:冲压机与冲模 10 POS MOD PLUG PRO-CRIMP DIE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5856-1 WH005 | 制造商:Alpha Electronics Corporation 功能描述:EQUIPMENT WIRE 20AWG WHT |
| 58561 | 制造商:Alpha Wire Company 功能描述:WIRE UL1213 20 AWG WHITE 30.5M |
| 5856-10 VI005 | 制造商:Alpha Electronics Corporation 功能描述:EQUIPMENT WIRE 20AWG PUR |
| 585610 | 制造商:Alpha Wire Company 功能描述:WIRE UL1213 20 AWG VIOLET 30.5M |
发布紧急采购，3分钟左右您将得到回复。