- 您现在的位置：买卖IC网 > Datasheet目录601 > 58605-2 (TE Connectivity)PROCRIMP DIE JPT W/SEAL Datasheet资料下载
参数资料
| 型号： | 58605-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | PROCRIMP DIE JPT W/SEAL |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 1.0-2.5mm² |
| 压接手柄： | Tyco/AMP 58605-1 |
| 连接器类型： | 压接端子 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q3911050 |
Figure 2
screw just enough to hold the dies in place. Do not
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with three
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the tool frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the long die retaining screw to hold the
locator assembly in place.
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long die retaining screw, and position the locator
assembly against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, locator assembly,
the two die retaining screws, and the four die
retaining pins, and slide the anvils and crimpers out
of the tool jaws.
相关PDF资料 |
PDF描述 |
|---|---|
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 586052-1 | 制造商:RAYTHN 功能描述: |
| 586-0556-5-55 | 制造商:Hirose 功能描述: |
| 58606-1 | 功能描述:折皱器 PROCRIMP 1.5 & 2.5MM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58-606152-21G | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 58-606152-21P | 制造商:Amphenol Aerospace 功能描述: |
发布紧急采购，3分钟左右您将得到回复。