- 您现在的位置：买卖IC网 > Datasheet目录601 > 58605-2 (TE Connectivity)PROCRIMP DIE JPT W/SEAL Datasheet资料下载
参数资料
| 型号： | 58605-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | PROCRIMP DIE JPT W/SEAL |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 1.0-2.5mm² |
| 压接手柄： | Tyco/AMP 58605-1 |
| 连接器类型： | 压接端子 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q3911050 |
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
must face the top of the tool. Place the contact up
into the nest so that the movable locator drops into
the slot in the contact. Refer to Figure 3. Butt the
front end of the wire barrel against the movable
locator.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire (with the wire seal) into
contact insulation and wire barrels until it is butted
against the wire stop, as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
7. Check the contact crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, CRIMP HEIGHT ADJUSTMENT.
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp–height comparator. Tyco
Electronics does not manufacture or market
crimp–height comparators. Detailed information on
obtaining and using crimp–height comparators can be
found in instruction sheet 408–7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
CRIMP HEIGHT ADJUSTMENT.
Figure 4
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel counterclockwise to a higher–numbered
setting. If a looser crimp is required, rotate the
adjustment wheel clockwise to a lower–numbered
setting.
4. Re–assemble the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Figure 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 586052-1 | 制造商:RAYTHN 功能描述: |
| 586-0556-5-55 | 制造商:Hirose 功能描述: |
| 58606-1 | 功能描述:折皱器 PROCRIMP 1.5 & 2.5MM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58-606152-21G | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 58-606152-21P | 制造商:Amphenol Aerospace 功能描述: |
发布紧急采购，3分钟左右您将得到回复。