- 您现在的位置：买卖IC网 > Datasheet目录601 > 58605-2 (TE Connectivity)PROCRIMP DIE JPT W/SEAL Datasheet资料下载
参数资料
| 型号： | 58605-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | PROCRIMP DIE JPT W/SEAL |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | 1.0-2.5mm² |
| 压接手柄： | Tyco/AMP 58605-1 |
| 连接器类型： | 压接端子 |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q3911050 |
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimp section according
to the wire size markings on the tool. Refer to
Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact—insulation barrel first—through the front of
the tool and into the appropriate crimp section.
Figure 3
相关PDF资料 |
PDF描述 |
|---|---|
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
| 58707-2 | TOOL DIE SET ONLY 16-20 AWG |
| 59239-8 | TOOL HAND 10-12AWG 14-16AWG HD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 586052-1 | 制造商:RAYTHN 功能描述: |
| 586-0556-5-55 | 制造商:Hirose 功能描述: |
| 58606-1 | 功能描述:折皱器 PROCRIMP 1.5 & 2.5MM RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58-606152-21G | 制造商:Amphenol Aerospace 功能描述:CONNECTOR |
| 58-606152-21P | 制造商:Amphenol Aerospace 功能描述: |
发布紧急采购，3分钟左右您将得到回复。