- 您现在的位置：买卖IC网 > PDF目录39245 > 5962-9319501MYA (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PQCC44 PDF资料下载
参数资料
| 型号： | 5962-9319501MYA |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| 封装： | EL44A |
| 文件页数： | 16/43页 |
| 文件大小： | 991K |
| 代理商： | 5962-9319501MYA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
2.0 Internal User-Programmable
Registers (Continued)
Any Instruction RAM READ or WRITE can affect the se-
quencer’s operation:
The Sequencer should be stopped by setting the RESET
bit to a “1” or by resetting the START bit in the Configura-
tion Register and waiting for the current instruction to fin-
ish execution before any Instruction RAM READ or
WRITE is initiated.
A soft RESET should be issued by writing a “1” to the
Configuration Register’s RESET bit after any READ or
WRITE to the Instruction RAM.
The three sections in the Instruction RAM are selected by
the Configuration Register’s 2-bit “RAM Pointer”, bits D8 and
D9. The first 16-bit Instruction RAM section is selected with
the RAM Pointer equal to “00”. This section provides multi-
plexer channel selection, as well as resolution, acquisition
time, etc. The second 16-bit section holds “watchdog” limit
#1, its sign, and an indicator that shows that an interrupt can
be generated if the input signal is greater or less than the
programmed limit. The third 16-bit section holds “watchdog”
limit #2, its sign, and an indicator that shows that an interrupt
can be generated if the input signal is greater or less than the
programmed limit.
Instruction RAM “00”
Bit 0 is the LOOP bit. It indicates the last instruction to be ex-
ecuted in any instruction sequence when it is set to a “1”.
The next instruction to be executed will be instruction 0.
Bit 1 is the PAUSE bit. This controls the Sequencer’s opera-
tion. When the PAUSE bit is set (“1”), the Sequencer will stop
after reading the current instruction and before executing it,
and the start bit in the Configuration register is automatically
reset to a “0”. Setting the PAUSE also causes an interrupt to
be issued. The Sequencer is restarted by placing a “1” in the
Configuration register’s Bit 0 (Start bit).
After the Instruction RAM has been programmed and the
RESET bit is set to “1”, the Sequencer retrieves Instruction
000, decodes it, and waits for a “1” to be placed in the Con-
figuration’s START bit. The START bit value of “0” “over-
rides” the action of Instruction 000’s PAUSE bit when the Se-
quencer is started. Once started, the Sequencer executes
Instruction 000 and retrieves, decodes, and executes each
of the remaining instructions. No PAUSE Interrupt (INT 5) is
generated the first time the Sequencer executes Instruction
000 having a PAUSE bit set to “1”. When the Sequencer en-
counters a LOOP bit or completes all eight instructions, In-
struction 000 is retrieved and decoded. A set PAUSE bit in
Instruction 000 now halts the Sequencer before the instruc-
tion is executed.
Bits 2–4 select which of the eight input channels (“000” to
“111” for IN0–IN7) will be configured as non-inverting inputs
to the LM12(H)458’s ADC. (See Page 27,
Table 1.) They se-
lect which of the four input channels (“000” to “011” for
IN0–IN4) will be configured as non-inverting inputs to the
LM12454’s ADC. (See Page 27,
Table 2.)
Bits 5–7 select which of the seven input channels (“001” to
“111” for IN1 to IN7) will be configured as inverting inputs to
the LM12(H)458’s ADC. (See Page 27,
Table 1.) They select
which of the three input channels (“001” to “011” for IN1–IN4)
will be configured as inverting inputs to the LM12454’s ADC.
(See Page 27,
Table 2.) Fully differential operation is created
by selecting two multiplexer channels, one operating in the
non-inverting mode and the other operating in the inverting
mode. A code of “000” selects ground as the inverting input
for single ended operation.
Bit 8 is the SYNC bit. Setting Bit 8 to “1” causes the Se-
quencer to suspend operation at the end of the internal S/H’s
acquisition cycle and to wait until a rising edge appears at
the SYNC pin. When a rising edge appears, the S/H ac-
quires the input signal magnitude and the ADC performs a
conversion on the clock’s next rising edge. When the SYNC
pin is used as an input, the Configuration register’s “I/O Se-
lect” bit (Bit 7) must be set to a “0”. With SYNC configured as
an input, it is possible to synchronize the start of a conver-
sion to an external event. This is useful in applications such
as digital signal processing (DSP) where the exact timing of
conversions is important.
When the LM12(H)454/8 are used in the “watchdog” mode
with external synchronization, two rising edges on the SYNC
input are required to initiate two comparisons. The first rising
edge initiates the comparison of the selected analog input
signal with Limit #1 (found in Instruction RAM “01”) and the
second rising edge initiates the comparison of the same ana-
log input signal with Limit #2 (found in Instruction RAM “10”).
Bit 9 is the TIMER bit. When Bit 9 is set to “1”, the Se-
quencer will halt until the internal 16-bit Timer counts down
to zero. During this time interval, no “watchdog” comparisons
or analog-to-digital conversions will be performed.
Bit 10 selects the ADC conversion resolution. Setting Bit 10
to “1” selects 8-bit + sign and when reset to “0” selects 12-bit
+ sign.
Bit 11 is the “watchdog” comparison mode enable bit. When
operating in the “watchdog” comparison mode, the selected
analog input signal is compared with the programmable val-
ues stored in Limit #1 and Limit #2 (see Instruction RAM “01”
and Instruction RAM “10”). Setting Bit 11 to “1” causes two
comparisons of the selected analog input signal with the two
stored limits. When Bit 11 is reset to “0”, an 8-bit + sign or
12-bit + sign (depending on the state of Bit 10 of Instruction
RAM “00”) conversion of the input signal can take place.
www.national.com
23
相关PDF资料 |
PDF描述 |
|---|---|
| LM12H458MWG-MCP | SPECIALTY ANALOG CIRCUIT, CDFP44 |
| LM12H458MWG/883 | SPECIALTY ANALOG CIRCUIT, CDFP44 |
| LM1262NA/NOPB | 3 CHANNEL, VIDEO PREAMPLIFIER, PDIP24 |
| LM129BH/883 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, MBCY2 |
| LM129BH | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, MBCY2 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5962-9319801HXA | 功能描述:模数转换器 - ADC Analog to Digital Converter RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| 5962-9319801HXC | 功能描述:模数转换器 - ADC Analog to Digital Converter RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| 5962-9319803HXA | 功能描述:模数转换器 - ADC Analog to Digital Converter RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| 5962-9319803HXC | 功能描述:模数转换器 - ADC Analog to Digital Converter RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| 59629319901MXA | 制造商:TI 功能描述:SNJ54ABT16240WD |
发布紧急采购，3分钟左右您将得到回复。