- 您现在的位置：买卖IC网 > PDF目录97839 > 71M6515H-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP64 PDF资料下载
参数资料
| 型号： | 71M6515H-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 封装： | LEAD FREE, LQFP-64 |
| 文件页数： | 13/60页 |
| 文件大小： | 826K |
| 代理商： | 71M6515H-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
71M6515H
Energy Meter IC
DATA SHEET
JULY 2011
Page: 20 of 60
2005
2011 Teridian Semiconductor Corporation
1.6
A Maxim Integrated Products Brand
Internal Resources
Oscillator
The oscillator drives a standard 32.768kHz watch crystal. Crystals of this type are accurate and do not require a high current
oscillator circuit. The 71M6515H oscillator has been designed specifically to handle watch crystals and is compatible with their
high impedance and limited power handling capability. The oscillator power dissipation is very low to maximize the lifetime of
any battery backup device attached to VBAT. Using PLL techniques, all internal clocks, such as the 4.915MHz clock for the
ADC and the post-processor, are derived from the watch crystal frequency.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. In the absence of V3P3, it is powered by the battery-backed up supply. The
RTC consists of a counter chain and output registers. The counter chain consists of registers for seconds, minutes, hours, day
of week, day of month, month, and year. The nominal quadratic temperature coefficient of the crystal is automatically
compensated in the RTC. The RTC is capable of processing leap years.
I/O Peripherals
The 71M6515H includes several I/O peripheral functions that improve the functionality of the device and reduce the
component count for most meter applications. The I/O peripherals include a UART and digital I/O.
Digital I/O
The device includes eight pins of general purpose digital I/O (D0…D7). Each pin can be configured independently as an input
or output with the D_DIR bits. Inputs are standard CMOS with no pull-ups or pull-downs. Outputs are standard CMOS. The
DIO pins are controlled by the D_CONFIG register.
Immediately after reset or power-up, D0 through D7 are in tri-state mode. 140 ms after reset, D0 through D7 are con-
figured as outputs and driven low.
UART Host Interface
The UART is a dedicated 2-wire serial interface, which can communicate with the host processor. The operation of each pin is
as follows:
RX: Is the pin accepting the serial input data. It inputs data to internal registers. The bytes are input LSB first. The voltage
applied to this pin must be restricted to 0 to 3.6V.
TX: Is the pin used for serial output data. It outputs the contents of a block of internal registers. The bytes are output LSB
first.
BAUD_RATE: The baud rate can be selected with the BAUD_RATE pin (38.4bps when high, 19.2bps when low).
UARTCSZ: This pin enables the UART when low. The UART can be reset by taking UARTCSZ briefly to the high state and
then low again.
The 71M6515H has several on-chip registers, which can be read and written. All transfers start with a stream of 8-bit bytes
(LSB first) from the host on the RX input, followed by a (possibly null) stream of 8-bit bytes (LSB first) to the host on the TX
output (see Figure 9 and Figure 10). The UART is configured as 8N1 (8 bits, no parity, 1 stop bit).
If the READY bit in STMASK is enabled, the IRQZ pin can be used to signal data availability to the host. If data read cycles
exceeding 1 second are used, care should be taken to prevent data overflow.
UART Write Register Operation
The registers are written by sending a byte, consisting of a starting register address in the seven MSBs and ‘0’ in the LSB
indicating this is a write operation. It is followed by a one byte length of bytes to write. If more bytes arrive than fit in the
addressed register, subsequent registers will be written. The bytes are processed in “big-endian” order (i.e. most significant
byte first). See Figure 9 (read bits and bytes from left to right).
相关PDF资料 |
PDF描述 |
|---|---|
| 7234 | SPECIALTY ANALOG CIRCUIT, CDIP22 |
| 7244 | SPECIALTY ANALOG CIRCUIT, PDIP20 |
| 7250 | SPECIALTY ANALOG CIRCUIT, PDIP16 |
| 73S8009CN-32IMR/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
| 73S8009CN-32IM/F | SPECIALTY ANALOG CIRCUIT, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6515H-IGTR | 制造商:Maxim Integrated Products 功能描述:71M6515H-IGT - T/REEL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Energy Meter IC |
| 71M6515H-IGTR/F | 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6515H-IGTW/F | 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6515H-IGTW1 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
| 71M6515H-IGTWR1 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
发布紧急采购，3分钟左右您将得到回复。