参数资料
型号: 71M6515H-IGT/F
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, PQFP64
封装: LEAD FREE, LQFP-64
文件页数: 52/60页
文件大小: 826K
代理商: 71M6515H-IGT/F
71M6515H
Energy Meter IC
DATA SHEET
JULY 2011
Page: 56 of 60
2005
2011 Teridian Semiconductor Corporation
1.6
A Maxim Integrated Products Brand
Figure 20: Timing Diagram (Host Polling)
Communication Steps for Interrupt Method:
The following is a list of commands required from the host processor to establish communication with the 71M6515H.
1)
Establish host baud rate and data format as required by the 71M6515H.
2)
Configure the DIO pins (D0…D7), if required, using the D_CONFIG register
3)
Configure the 71M6515H by selecting the CE image (bits 23-22), equation (bits 7-5), pulse rate (bits 26-25), followed
by enabling the CE (bit 4 in the CONFIG register). The bit pattern sent to CONFIG should have all bits set to their
default state, as given in the Register Table.
4)
Write the TEMP_RAW value obtained at calibration into the TEM_NOM register to enable temperature compensation.
5)
Write the calibration coefficients into registers CAL_IA, CAL_VA, CAL_IB, CAL_VB, CAL_C, CAL_VC, PHADJ_A,
PHADJ_B, PHADJ_C. Write calibration values to the VFEED_A/B/C registers if the Rogowski image is used.
6)
Configure WRATE with the value required to generate the desired pulse rate.
7)
Establish creep, sag and over/under voltage/current thresholds, if necessary, by writing values to the
CREEP_THRSLD, SAG, VI_PTHRESH, and VI_THRSHLD registers.
8)
Set the READY bit in the status mask STMASK in order to enable the generation of interrupts on the IRQZ pin.
9)
Read at least one accumulated value register (WATTH_X, or VAH_X, or VARH_X).
10) Wait for the IRQZ pin to go low.
11) After receiving the interrupt, read at least one accumulated value register (WATTH_X, or VAH_X, or VARH_X) in order
to maintain interrupt generation. Read the bits in the STATUS word to detect potential faults (overflow signaled by the
XOVF flag or uninitialized condition signaled by the BOOTUP flag) or warnings and events (sag, creep, excessive
voltage or current, DIO signal changes). If necessary, take corrective action.
12) After reading the required data from the 71M6515H, configuration changes should be made, if necessary. These con-
figuration changes should be completed before the pre-processing period begins again.
1000ms
2000ms
330ms
read
commands
fromhost
read
commands
fromhost
6515H not
ready
6515H not
ready
post-processor
active
post-processor
active
330ms
6515H data
time
相关PDF资料
PDF描述
7234 SPECIALTY ANALOG CIRCUIT, CDIP22
7244 SPECIALTY ANALOG CIRCUIT, PDIP20
7250 SPECIALTY ANALOG CIRCUIT, PDIP16
73S8009CN-32IMR/F SPECIALTY ANALOG CIRCUIT, QCC32
73S8009CN-32IM/F SPECIALTY ANALOG CIRCUIT, QCC32
相关代理商/技术参数
参数描述
71M6515H-IGTR 制造商:Maxim Integrated Products 功能描述:71M6515H-IGT - T/REEL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Energy Meter IC
71M6515H-IGTR/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6515H-IGTW/F 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6515H-IGTW1 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation
71M6515H-IGTWR1 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation