参数资料
型号: 71M6532F-IGT/F
厂商: Maxim Integrated
文件页数: 61/121页
文件大小: 0K
描述: IC ENERGY METER 256KB 100-LQFP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 90
系列: *
FDS 6531/6532 005
Data Sheet 71M6531D/F-71M6532D/F
2.5
Wake-Up Behavior
As described above, the part will always wake up in MISSION mode when system power is restored.
Additionally, the part will wake up in BROWNOUT mode when PB rises (push button is pressed) or when
a timeout of the wake-up timer occurs.
2.5.1
Wake on PB
If the part is in SLEEP or LCD mode, it can be awakened by a rising edge on the PB pin. This pin is normally
pulled to GND and can be pulled high by a push button depression. Before the PB signal rises, the MPU
is in reset due to WAKE being low. When PB rises, WAKE rises and within three crystal cycles, the MPU
begins to execute. The MPU can determine whether the PB signal woke it up by checking the IE_PB flag.
Figure 25 shows the Wake Up timing.
For debouncing, the PB pin is monitored by a state machine operating from a 32 Hz clock. This circuit
will reject between 31 ms and 62 ms of noise. Detection hardware will ignore all transitions after the initial
rising edge. This will continue until the MPU clears the IE_PB bit.
Figure 25: Wake Up Timing
2.5.2
Wake on Timer
If the part is in SLEEP or LCD mode, it can be awakened by the wake-up timer. Until this timer times out,
the MPU is in reset due to WAKE being low. When the wake-up timer times out, the WAKE signal rises
and within three crystal cycles, the MPU begins to execute. The MPU can determine whether the timer
woke it by checking the AUTOWAKE interrupt flag ( IE_WAKE ).
The wake-up timer begins timing when the part enters LCD or SLEEP mode. Its duration is controlled by
WAKE_PRD[2:0] and WAKE_RES . WAKE_RES selects a timer LSB of either 1 minute ( WAKE_RES = 1) or
2.5 seconds ( WAKE_RES = 0). WAKE_PRD[2:0] selects a duration of from 1 to 7 LSBs.
The timer is armed by WAKE_ARM = 1. It must be armed at least three RTC cycles before SLEEP or
LCD_ONLY is initiated. Setting WAKE_ARM presets the timer with the values in WAKE_RES and WAKE_PRD
and readies the timer to start when the processor writes to SLEEP or LCD_ONLY. The timer is reset and
disarmed whenever the processor is awake. Thus, if it is desired to wake the MPU periodically (every 5
seconds, for example) the timer must be rearmed every time the MPU is awakened.
2.6
Data Flow
VB, performing calculations to measure active power (Wh), reactive power (VARh), A h and V h for four-
The data flow between the Compute Engine (CE) and the MPU is shown in Figure 26. In a typical ap-
plication, the 32-bit CE sequentially processes the samples from the voltage inputs on pins IA, VA, IB and
2 2
quadrant metering. These measurements are then accessed by the MPU, processed further and output
using the peripheral devices available to the MPU.
Rev 2
61
相关PDF资料
PDF描述
R1S12-1212/H CONV DC/DC 1W 12VIN 12VOUT
VI-BNW-EU-F3 CONVERTER MOD DC/DC 5.5V 200W
LM285MX-2.5/NOPB IC VREF SHUNT 2.5V 8-SOIC
RCD-24-1.20/W LED DRVR CONST 1.2A 3-33VOUT
78M6618-M/F/P1 IC PWR MEASUREMENT OCTAL 68QFN
相关代理商/技术参数
参数描述
71M6532F-IGTR/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6532F-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6533 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC
71M6533-DB 功能描述:开发板和工具包 - 8051 71M6533 Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
71M6533G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Exceeds IEC 62053/ANSI C12.20 Standards