- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6542G-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6542G-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 152/165页 |
| 文件大小： | 2208K |
| 代理商： | 71M6542G-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页当前第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
v1.1
2008–2011 Teridian Semiconductor Corporation
87
There is no internal digital state that could deactivate the WDT. For debug purposes, however, the WDT
can be disabled by raising the ICE_E pin to 3.3 VDC.
In normal operation, the WDT is reset by periodically writing a one to the WD_RST control bit (I/O RAM
0x28B4[7]). The watchdog timer is also reset when the 71M654x wakes from LCD or SLP mode, and
when ICE_E = 1.
3.4
Wake Up Behavior
As described above, the part always wakes-up in MSN mode when system power is restored. As
described in 3.2 Battery Modes, transitions from both LCD and SLP mode to BRN mode can be initiated
by a wake-up timer timeout, when the pushbutton (PB) input is high, a high level on SEGDIO4,
SEGDIO52 or SEGDIO55, or by activity on the RX or OPT_RX pins.
3.4.1
Wake on Hardware Events
The following pin signal events wake the 71M654x from SLP or LCD mode: a high level on the PB pin, either
edge on the RX pin, a rising edge on the SEGDIO4 pin, a high level on the SEGDIO52 pin (71M6542F only),
or a high level on the SEGDIO55 pin or either edge on the OPT_RX pin. See Table 69 for de-bounce details
on each pin and for further details on the OPT_RX/SEGDIO55 pin. The SEGDIO4, SEGDIO52 (71M6542F
only), and SEGDIO55 pins must be configured as DIO inputs and their wake enable (EW_x bits) must be
set. In SLP and LCD modes, the MPU is held in reset and cannot poll pins or react to interrupts. When
one of the hardware wake events occurs, the internal WAKE signal rises and within three CK32 cycles
the MPU begins to execute. The MPU can determine which one of the pins awakened it by checking the
WF_PB, WF_RX, WF_SEGDIO4, WF_DIO52 (71M6542F only), or WF_DIO55 flags (see Table 69).
If the part is in SLP or LCD mode, it can be awakened by a high level on the PB pin. This pin is normally
pulled to GND and can be connected externally so it may be pulled high by a push button depression.
Some pins are de-bounced to reject EMI noise. Detection hardware ignores all transitions after the initial
transition. Table 69 shows which pins are equipped with de-bounce circuitry.
Pins that do not have de-bounce circuits must still be high for at least 2 s to be recognized.
The wake enable and flag bits are also shown in Table 69. The wake flag bits are set by hardware when
the MPU wakes from a wake event. Note that the PB flag is set whenever the PB is pushed, even if the
part is already awake.
Table 71 lists the events that clear the WF flags.
In addition to push buttons and timers, the part can also reboot due to the RESET pin, the RESET bit (I/O
RAM 0x2200[3]), the WDT, the cold start detector, and E_RST. As seen in Table 69, each of these
mechanisms has a flag bit to alert the MPU to the source of the wakeup. If the wake-up is caused by
return of system power, there is no active WF flag and the VSTAT[2:0] field (SFR 0xF9[2:0]) indicate that
system power is stable.
Table 69: Wake Enables and Flag Bits
Wake Enable
Wake Flag
De-bounce
Description
Name
Location
Name
Location
WAKE_ARM
28B2[5]
WF_TMR
28B1[5]
No
Wake on Timer.
EW_PB
28B3[3]
WF_PB
28B1[3]
Yes
Wake on PB*.
EW_RX
28B3[4]
WF_RX
28B1[4]
2 s
Wake on either edge of RX.
EW_DIO4
28B3[2]
WF_DIO4
28B1[2]
2 s
Wake on SEGDIO4.
EW_DIO52
28B3[1]
WF_DIO52
28B1[1]
Yes
Wake on SEGDIO52*.
EW_DIO55
28B3[0]
WF_DIO55
28B1[0]
Yes
OPT_RXDIS = 1: Wake on DIO55*
with 64 ms de-bounce.
OPT_RXDIS = 0: Wake on either
edge of OPT_RX with 2 s de-
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6541G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541D-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6542F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6541D-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6542GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Bulk |
| 71M6542GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Tape and Reel |
| 71M6543F | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543F-DB | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6543F-DB-CT | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。