- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6542G-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6542G-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 79/165页 |
| 文件大小： | 2208K |
| 代理商： | 71M6542G-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页当前第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
20
2008–2011 Teridian Semiconductor Corporation
v1.1
360
o -
θ, resulting in the residual phase error between the current and its corresponding voltage of θ – Ф.
The residual phase error is negligible, and is typically less than ±1.5 milli-degrees at 100Hz, thus it does
not contribute to errors in the energy measurements.
When using remote sensors, the CE performs the same delay compensation described above to align
each voltage sample with its corresponding current sample. Even though the remote current samples do
not pass through the 71M654x multiplexer, their timing relationship to their corresponding voltages is
fixed and precisely known, provided that the MUXn_SEL[3:0] slot assignment fields are programmed as
shown in Table 1 and Table 2.
2.2.4
ADC Pre-Amplifier
The ADC pre-amplifier is a low-noise differential amplifier with a fixed gain of 8 available only on the IAP-
IAN sensor input pins. A gain of 8 is enabled by setting PRE_E = 1 (I/O RAM 0x2704[5]). When disabled,
the supply current of the pre-amplifier is <10 nA and the gain is unity. With proper settings of the PRE_E
and DIFFA_E (I/O RAM 0x210C[4]) bits, the pre-amplifier can be used whether differential mode is
selected or not. For best performance, the differential mode is recommended. In order to save power, the
bias current of the pre-amplifier and ADC is adjusted according to the ADC_DIV control bit (I/O RAM
0x2200[5]).
2.2.5
A/D Converter (ADC)
A single 2
nd order delta-sigma A/D converter digitizes the voltage and current inputs to the device. The
resolution of the ADC, including the sign bit, is 21 bits (FIR_LEN[1:0] = 1, I/O RAM 0x210C[2:1]), or 22 bits
(FIR_LEN[1:0] = 2). The ADC is clocked by CKADC.
Initiation of each ADC conversion is controlled by MUX_CTRL internal circuit as described above. At the
end of each ADC conversion, the FIR filter output data is stored into the CE RAM location determined by
the multiplexer selection. FIR data is stored LSB justified, but shifted left 9 bits.
2.2.6
FIR Filter
The finite impulse response filter is an integral part of the ADC and it is optimized for use with the multiplexer.
The purpose of the FIR filter is to decimate the ADC output to the desired resolution. At the end of each
ADC conversion, the output data is stored into the fixed CE RAM location determined by the multiplexer
2.2.7
Voltage References
A bandgap circuit provides the reference voltage to the ADC. The amplifier within the reference is chopper
stabilized, i.e., the chopper circuit can be enabled or disabled by the MPU using the I/O RAM control field
CHOP_E[1:0] (I/O RAM 0x2106[3:2]). The two bits in the CHOP_E[1:0] field enable the MPU to operate the
chopper circuit in regular or inverted operation, or in toggling modes (recommended). When the
chopper circuit is toggled in between multiplexer cycles, dc offsets on VREF are automatically be
averaged out, therefore the chopper circuit should always be configured for one of the toggling modes.
Since the VREF band-gap amplifier is chopper-stabilized, the dc offset voltage, which is the most
significant long-term drift mechanism in the voltage references (VREF), is automatically removed by the
chopper circuit. Both the 71M654x and the 71M6x01 feature chopper circuits for their respective VREF
voltage reference.
The general topology of a chopped amplifier is shown in Figure 8. The CROSS signal is an internal on-
chip signal and is not accessible on any pin or register.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6541G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541D-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6542F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6541D-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6542GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Bulk |
| 71M6542GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Tape and Reel |
| 71M6543F | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543F-DB | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6543F-DB-CT | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。