- 您现在的位置：买卖IC网 > PDF目录16281 > 73S8014RN-DB (Maxim Integrated Products)BOARD DEMO 73S8010RN 20-SOIC PDF资料下载
参数资料
| 型号： | 73S8014RN-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 73S8010RN 20-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
DS_8014RN_014
73S8014RN Data Sheet
Rev. 1.0
19
3.9
Fault Detection and
OFF
There are two different cases that the system controller can monitor the
OFF signal: to query regarding the card
presence outside card sessions, or for fault detection during card sessions.
Outside a card session: In this condition,
CMDVCC is always high, OFF is low if the card is not present, and high
if the card is present. Because it is outside a card session, any fault detection will not act upon the
OFF signal.
No deactivation is required during this time.
During a card session:
CMDVCC is always low, and OFF falls low if the card is extracted or if any fault detection
is detected. At the same time that
OFF is set low, the sequencer starts the deactivation process.
Figure 7 shows the timing diagram for the signals
CMDVCC, PRES, and OFF during a card session and outside
the card session:
e
the card session:
PRES
OFF
CMDVCC
VCC
PRES
OFF
CMDVCC
VCC
outside card session
within card session
OFFis lowby
card extracted
OFFis lowby
anyfault
within card
session
Figure 7: Timing Diagram – Management of the Interrupt Line
OFF
3.10 I/O Circuitry and Timing
The state of the I/O pin is low after power on reset and it goes high when the activation sequencer turns on the
I/O reception state. See the Activation Sequence section for details on when the I/O reception is enabled. The
state of I/OUC is high after power on reset.
Within a card session and when the I/O reception state is turned on, the first I/O line on which a falling edge is
detected becomes the input I/O line and the other becomes the output I/O line. When the input I/O line rising
edge is detected then both I/O lines return to their neutral state.
Note: In certain situations and conditions, the I/O logic can get confused if the host and the card attempt to drive
the IOUC and the I/O signal low at the same time. It should be noted that this is an illegal condition as all card
communication is initiated by the host with a command/response protocol. The next host command should not be
sent until a valid response has been completely received from the card. However, if this condition should occur,
the 8014 may set both the IOUC and the I/O as outputs where they are both driven low at the same time. When
either side drives their respective signal high, then this mode should be released. However, if there is a series
resistance between the host and the 8014, then there may not be enough drive to release this mode. If the series
resistance is greater than about 100 ohms, then this may cause this mode to become locked for the duration of
the card session. If the host detects this condition (IOUC held low for more than one byte time), the card session
must be terminated and restarted.
Figure 8 shows the state diagram of how the I/O and I/OUC lines are managed to become input or output. The
delay between the I/O signals is shown in Figure 9.
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8014R-DB | BOARD DEMO 73S8010R 20-SOIC |
| 73S8024RN-DB | BOARD DEMO 73S8024RN 28-SOIC |
| M3CKK-2018R | IDC CABLE - MKC20K/MC20M/MPK20K |
| M3AKK-2018R | IDC CABLE - MSC20K/MC20M/MPK20K |
| M3TTK-2618R | IDC CABLE - MSD26K/MC26M/MSD26K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8014RN-IL/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F1 | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F2 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F3 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-ILR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。