- 您现在的位置：买卖IC网 > PDF目录16281 > 73S8014RN-DB (Maxim Integrated Products)BOARD DEMO 73S8010RN 20-SOIC PDF资料下载
参数资料
| 型号： | 73S8014RN-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/28页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 73S8010RN 20-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页
73S8014RN Data Sheet
DS_8014RN_014
6
Rev. 1.0
Table 1 provides the 73S8014RN pin names, pin numbers, type, equivalent circuits and descriptions.
Table 1: 73S8014RN 20-Pin SOP Pin Definitions
Pin Name
Pin
Number
Type
Equivalent
Circuit
Description
Card Interface
I/O
14
IO
Card I/O: Data signal to/from card. Includes an 11K pull-up
resistor to VCC.
RST
15
O
Card reset: provides reset (RST) signal to card.
CLK
17
O
Card clock: provides clock signal (CLK) to card. The rate of this
clock is determined by the external crystal frequency or
frequency of the external clock signal applied on XTALIN and
CLKDIV selections.
PRES
19
I
Card Presence switch: active high indicates card is present.
Includes a high-impedance pull-down current source.
VCC
18
PSO
Card power supply – logically controlled by sequencer, output of
LDO regulator. Requires an external filter capacitor to the card
GND.
GND
16
GND
–
Card ground.
Host Processor Interface
CMDVCC
6
I
Command VCC (negative assertion): Logic low on this pin
causes the LDO regulator to ramp the VCC supply to the card
and initiates a card activation sequence, if a card is present.
5V/
#V
7
I
5 volt / 3 volt card selection: Logic high selects 5 volts for VCC
and card interface, logic low selects 3 volt operation. When the
part is to be used with a single card voltage, this pin should be
tied to either GND or VDD. However, it includes a high
impedance pull-up resistor to default this pin high (selection of
5V card) when not connected. This pin shall not be changed
when
CMDVCC is low.
CLKDIV1
CLKDIV2
20
5
I
Sets the divide ratio from the XTAL oscillator (or external clock
input) to the card clock. These pins include a pull-up resistor for
CLKDIV1 and CLKLDIV2 to provide a default rate of divide by
two.
CLKDIV1
CLKDIV2
CLOCK RATE
0
XTALIN/6
0
1
XTALIN/4
1
XTALIN/2
1
0
XTALIN
OFF
1
O
Interrupt signal to the processor. Active Low - Multi-function
indicating fault conditions and card presence. Open drain output
configuration – It includes an internal 20k pull-up to VDD.
RSTIN
2
I
Reset Input: This signal is the reset command to the card.
I/OUC
3
IO
System controller data I/O to/from the card. Includes an 11K
pull-up resistor to VDD.
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8014R-DB | BOARD DEMO 73S8010R 20-SOIC |
| 73S8024RN-DB | BOARD DEMO 73S8024RN 28-SOIC |
| M3CKK-2018R | IDC CABLE - MKC20K/MC20M/MPK20K |
| M3AKK-2018R | IDC CABLE - MSC20K/MC20M/MPK20K |
| M3TTK-2618R | IDC CABLE - MSD26K/MC26M/MSD26K |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8014RN-IL/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F1 | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F2 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-IL/F3 | 功能描述:输入/输出控制器接口集成电路 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
| 73S8014RN-ILR/F | 功能描述:输入/输出控制器接口集成电路 Smart Card Interface Comp w/8024 RoHS:否 制造商:Silicon Labs 产品: 输入/输出端数量: 工作电源电压: 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。