- 您现在的位置：买卖IC网 > Datasheet目录611 > 90313-2 (TE Connectivity)SAHT Datasheet资料下载
参数资料
| 型号： | 90313-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SAHT |
| 标准包装： | 1 |
| 系列： | Certi-Crimp |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | FFC，FPC（扁平柔性）触点，26-32 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 88017-6-ND - CONN CONTACT SOCKET 26-32AWG FFC |
2. Make certain all pivot points and bearing
surfaces are protected with a THIN coat of any
good SAE 20 motor oil. Do NOT oil excessively.
3. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged
between the crimping dies, and store the tool in a
clean, dry area.
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to
supervisory personnel responsible for the tool.
Though recommendations call for at least one
inspection a month, the inspection frequency should
be based on the amount of use, ambient working
conditions, operator training and skill, and established
company standards. These visual inspections should
be performed in the following sequence:
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) in a
suitable commercial degreaser that will not affect
paint or plastic material.
2. Make certain all retaining pins are in place and
secured with retaining rings. If replacements are
necessary, refer to parts listed in Figure 5.
3. Close the tool handles until the ratchet releases,
then allow handles to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced (see Section 6, REPLACEMENT
AND REPAIR).
4. Inspect the head assembly, with special
emphasis on checking for worn, cracked, or broken
Proceed as follows:
1. Refer to Figure 4, and select a contact and a
maximum wire size for each crimping chamber.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the contacts accordingly.
3. Using a crimp height comparator, measure wire
barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in Figure 4,
the tool is considered dimensionally correct. If not,
return the tool for evaluation and repair (see
Section 6, REPLACEMENT AND REPAIR).
For additional information concerning the use of the
crimp height comparator, refer to Instruction Sheet
408–7424.
dies. If damage to any part of the head assembly is
evident, return the tool to Tyco Electronics for
evaluation and repair (see Section 6,
REPLACEMENT AND REPAIR).
88048–3
88048–5
1–88048–0
1–88048–3
28
28–32
.058
[.0230
.02
.0010]
88017–6
This inspection requires the use of a micrometer with
a modified anvil as shown in Figure 4. Tyco
88017–7
1–88017–8
1–88017–7
26
26
.068
[.0270
.02
.0010]
Electronics recommends the modified micrometer
(Crimp Height Comparator RS–1019–5LP) which can
be purchased from:
Figure 4
Shearer Industrial Supply Co.
717–767–7575
or
VALCO
610–691–3205
相关PDF资料 |
PDF描述 |
|---|---|
| 90327-1 | SAHT TYPE VI |
| 90348-2 | DIE W/O 69710-1 8 F IS7918 |
| 90381-1 | S.A.H.T |
| 90384-1 | TOOL 10AWG CPC SERIES 3 CRIMP |
| 90390-3 | DIE SET ULTRA-FASTONS 22-18 AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 903-135 | 功能描述:支架与垫片 Plastic Spcr .135 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90313A204 | 制造商:WASHERS 功能描述: |
| 9031-3CC | 制造商:Carlisle Interconnect Components 功能描述:RF COAXIAL PANEL MOUNT CONNECTOR |
| 9031-3CCSF | 制造商:Carlisle Interconnect Components 功能描述:RF COAXIAL PANEL MOUNT CONNECTOR |
| 9031-3SF | 制造商:Carlisle Interconnect Components 功能描述:RF COAXIAL PANEL MOUNT CONNECTOR |
发布紧急采购，3分钟左右您将得到回复。