- 您现在的位置：买卖IC网 > Datasheet目录611 > 90327-1 (TE Connectivity)SAHT TYPE VI Datasheet资料下载
参数资料
| 型号： | 90327-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | SAHT TYPE VI |
| 标准包装： | 5 |
| 系列： | Certi-Crimp, 多配接 VI 型 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 背板和圆形触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 66591-4-ND - CONN PIN 18-22 AWG GOLD CRIMP 66592-4-ND - CONN SOCKET 18-22 AWG GOLD CRIMP 66591-1-ND - CONN PIN 18-22 AWG TIN CRIMP 66591-2-ND - CONN PIN 18-22 AWG GOLD CRIMP 66592-2-ND - CONN SOCKET 18-22 AWG GOLD CRIMP |
408-7716
Back of Tool
(Wire Side)
Contact Support
Wire Size Marking
Mating End of Contact
Crimpers
Wire Slot in Locator
Contact Wire Barrel Against
Locator/Insulation Stop
Stripped Wire
Anvils
Figure 3
Locator/Insulation
Stop Entering Contact
Locator Slot
NOTE
i
If using strip-form contact, the cutoff tabs MUST
meet the dimension requirement stated on the
customer drawing for the product or Application
Specification 114-10007.
Proceed as follows:
1. Hold tool so BACK side (wire side) faces you.
Crimp Inspection Wire Barrel Seam Must Be Closed
with No Wire Strands Showing
Wire Conductor Must Be Flush
with or Protrude Slightly from
Wire Barrel
2. Ensure that the tool ratchet is released by
squeezing tool handles and allowing them to open.
3. Insert contact, mating end first, into the crimping
chamber from the BACK of tool. Position contact
between crimpers so that the locator/insulation stop
enters the contact locator slot. Make sure that the
wire barrel butts against the locator/insulation stop.
See Figure 3.
Contact Must Be
Straight
Wire Insulation Must
Be Visible in This Area
Locking Lance Must
Not Be Deformed
Figure 4
4. Holding the contact in position, squeeze the tool
handles together until insulation barrel anvil starts
entry into the insulation crimper. Do NOT deform
contact insulation barrel or wire barrel.
NOTE
i
For detailed crimp inspection requirements, refer to
Application Specification 114-10007.
5. Insert a properly stripped wire through the wire
slot in the locator and into the contact wire barrel
until the wire insulation butts against the locator/
insulation stop.
6. Holding the wire in place, squeeze the tool
handles together until the ratchet releases. Allow
tool handles to open FULLY.
7. Remove crimped contact from tool, and inspect
the crimp according to Figure 4.
Rev D
4. INSULATION CRIMP ADJUSTMENT
The insulation barrel crimp height is regulated by the
insulation crimp adjustment lever. To determine the
proper setting, test crimp a contact using the setting
which approximates the wire insulation size: 1-small,
2-medium, or 3-large. If the crimped insulation barrel
is too tight or too loose, change the setting
accordingly. The crimp should hold the wire insulation
firmly without cutting into it.
2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90348-2 | DIE W/O 69710-1 8 F IS7918 |
| 90381-1 | S.A.H.T |
| 90384-1 | TOOL 10AWG CPC SERIES 3 CRIMP |
| 90390-3 | DIE SET ULTRA-FASTONS 22-18 AWG |
| 90431-1 | TOOL CERTI-CRIMP HAND 20-24AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 903273304 | 制造商:Molex 功能描述: |
| 90327-3304 | 功能描述:集管和线壳 4CKT IDT RECPT LO PROFILE RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 903273306 | 制造商:Molex 功能描述: |
| 90327-3306 | 功能描述:集管和线壳 PICOFLEX 6P HSG LOPRO IDT AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 903273308 | 制造商:Molex 功能描述: |
发布紧急采购，3分钟左右您将得到回复。