- 您现在的位置：买卖IC网 > Datasheet目录611 > 90327-1 (TE Connectivity)SAHT TYPE VI Datasheet资料下载
参数资料
| 型号： | 90327-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | SAHT TYPE VI |
| 标准包装： | 5 |
| 系列： | Certi-Crimp, 多配接 VI 型 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 背板和圆形触点，18-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 配用： | 66591-4-ND - CONN PIN 18-22 AWG GOLD CRIMP 66592-4-ND - CONN SOCKET 18-22 AWG GOLD CRIMP 66591-1-ND - CONN PIN 18-22 AWG TIN CRIMP 66591-2-ND - CONN PIN 18-22 AWG GOLD CRIMP 66592-2-ND - CONN SOCKET 18-22 AWG GOLD CRIMP |
408-7716
5. MAINTENANCE AND INSPECTION
The tool is inspected before shipment. It is
recommended that the tool be inspected immediately
upon arrival at your facility to ensure that the tool was
not damaged during shipment and that it conforms to
the dimensions provided in Figure 6.
5.1. Daily Maintenance
1. Remove all foreign particles with a clean, soft
brush, or a clean, soft, lint-free cloth. Make sure the
proper retaining pins are in place, and secured with
the proper retaining rings. If foreign matter cannot
be removed easily, or if the proper replacement
parts are needed, refer to Section 6,
REPLACEMENT AND REPAIR.
2. Make certain all pivot points and bearing surfaces
are protected with a THIN coat of any good SAE 20
motor oil. Do NOT oil excessively.
3. When tool is not in use, keep the handles closed
to prevent objects from becoming lodged between
the crimping dies, and store the tool in a clean, dry
area.
5.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool and/or be supplied to
personnel responsible for the tool. Though
recommendations call for at least one inspection a
month, the inspection frequency should be based on
the amount of use, ambient working conditions,
operator training and skill, and established company
B. Crimp Height Inspection
Refer to Figure 5.
Crimp height inspection is performed through the
use of a micrometer with a modified anvil,
commonly referred to as a crimp height comparator. ?
TE does not market crimp height comparators.
Refer to Instruction Sheet 408-7424 for detailed
information on obtaining and using a crimp height
comparator.
To measure the crimp height, proceed as follows:
1. Select a contact and maximum size wire for the
tool.
2. Refer to Section 3, CRIMPING PROCEDURE,
and crimp the contact accordingly.
3. Using a crimp height comparator, measure wire
barrel crimp height as shown in Figure 5. If the
crimp height conforms to that shown, the tool is
considered dimensionally correct. If not, refer to
Section 6 for information on obtaining evaluation
and repair.
Spindle
standards. These inspections should be performed in
the following sequence:
A. Visual Inspection
Modified
Anvil
“A"
±0.05 [.002]
1. Remove all lubrication and accumulated film by
immersing the tool (handles partially closed) in a
suitable commercial degreaser that will not affect
paint or plastic material.
2. Make certain all retaining pins are in place and
secured with retaining rings. If replacements are
necessary, refer to Section 6.
CONTACT
NUMBER
66591
66592
66591
66592
WIRE SIZE,
AWG (MAX)
22
18
CRIMP SECT
(WIRE SIZE
MARKING)
22
18-20
CRIMP
HEIGHT DIM.
“A"
0.94 [.037]
1.12 [.044]
CAUTION Do NOT remove the retaining pins as permanent
damage to the tool may result.
!
C. Ratchet Inspection
Figure 5
3. Close the tool handles until the ratchet releases,
then allow the tool handles to open freely. If handles
do not open quickly and fully, the spring is defective
and must be replaced (refer to Section 6,
REPLACEMENT AND REPAIR).
4. Inspect the head assembly, with special
emphasis on checking for worn, cracked, or broken
dies. If damage to any part of the head assembly is
evident, refer to Section 6.
Rev D
Obtain a 0.0254 [.001] shim that is suitable for
checking the clearance between the bottoming
surfaces of the dies. Proceed as follows:
1. Select a contact and maximum wire size for the
tool.
2. Position the contact and wire between the dies,
according to Section 3, CRIMPING PROCEDURE.
Holding the wire in place, squeeze the tool handles
together until the ratchet releases. Hold the tool
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 90348-2 | DIE W/O 69710-1 8 F IS7918 |
| 90381-1 | S.A.H.T |
| 90384-1 | TOOL 10AWG CPC SERIES 3 CRIMP |
| 90390-3 | DIE SET ULTRA-FASTONS 22-18 AWG |
| 90431-1 | TOOL CERTI-CRIMP HAND 20-24AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 903273304 | 制造商:Molex 功能描述: |
| 90327-3304 | 功能描述:集管和线壳 4CKT IDT RECPT LO PROFILE RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 903273306 | 制造商:Molex 功能描述: |
| 90327-3306 | 功能描述:集管和线壳 PICOFLEX 6P HSG LOPRO IDT AU RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 903273308 | 制造商:Molex 功能描述: |
发布紧急采购，3分钟左右您将得到回复。