- 您现在的位置：买卖IC网 > Datasheet目录611 > 90752-1 (TE Connectivity)SEATING TOOL ASSY H.M. 110 PIN Datasheet资料下载
参数资料
| 型号： | 90752-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | SEATING TOOL ASSY H.M. 110 PIN |
| 标准包装： | 1 |
| 系列： | * |
408-9911
4. USING THE SEATING TOOL
1. Set the seating height to the dimension shown in
seating height PLUS the combined thicknesses of
the pc board and pc board support fixture).
2. Position the pin header onto pc board so that the
contacts are properly aligned with the holes in the
pc board and pc board support fixture.
3. Insert the pin header into pc board until the open
portion of the contacts are resting securely on, but
have not fully entered, the pc board.
4. Position the seating tool onto the pin header
making sure that the seating tool is bottomed on the
housing floor.
5. Center the seating tool and pin header under the
applicator ram of the power source; then slowly
lower the ram until it just meets the seating tool.
Verify the alignment of the pc board support fixture,
pc board, pin header, and seating tool.
5. MAINTENANCE AND INSPECTION
The seating tool is assembled and inspected before
shipment; however, it is recommended that the seating
tool be inspected immediately using Figure 3 upon
arrival at your facility to assure that it has not been
damaged during shipment.
5.1. Daily Maintenance
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint-free cloth. DO NOT
use objects that could damage any components of
the seating tool.
2. Ensure that the socket set screws are in place
and secured.
3. When the seating tool is not in use, store it in a
clean, dry area.
CAUTION
!
Damage to the pc board, seating tool, or pin header
may occur if the seating height is improperly set, or
if the seating tool is not properly seated on the pin
header before cycling the applicator ram.
5.2. Periodic Inspection
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the seating tool or be supplied to
6. Cycle the applicator ram according to instructions
included with the power source.
7. Check the pin header for proper seating using the
requirements in Application Specification 114-19029.
personnel responsible for the tool. The inspection
frequency should be based on the amount of use,
working conditions, operator training and skill, and
established company standards.
Note: Not to Scale
View After Seating
Applicator Ram (Fully Down) (Ref)
Seating Tool Centered Under
Applicator Ram
Applicator
Shut Height
(Ram Down)
Rev B
Seating Height
(Connector Seated)
38.1 +.254/-.000
[1.500 +.010/-.000]
Figure 2
Seating Tool Bottomed on
Housing Floor of Pin Header
Contacts Aligned With Holes in
PC Board and PC Board
Support Fixture
PC Board (Ref)
PC Board Support Fixture
(Ref)
2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 90754-3 | SEATING TOOL ASSY HM 95 PIN |
| 90756-1 | SEATING TOOL ASSY H.M. 55 PINS |
| 90757-1 | SEATING TOOL ASSY H.M. 77 PINS |
| 90758-2 | DIE SET FOR PRO-C III 26-22 AWG |
| 90759-2 | DIE SET FOR PRO-C III 22-20,18 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 907523-000 | 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 12AWG 3.71mm Tin Plated Copper White 600VAC 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 12AWG 3.71MM TN PLTD CPPR WH 600VAC - Cable Rools/Shrink Tubing |
| 907-525 | 功能描述:支架与垫片 Plastic Spcr .525 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 9075-2R | 制造商:GC Electronics 功能描述: |
| 907-530 | 功能描述:支架与垫片 Plastic Spcr .53 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90753-1 | 功能描述:手工工具 SEATING TOOL ASSY H. RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。