- 您现在的位置：买卖IC网 > Datasheet目录612 > 90758-2 (TE Connectivity)DIE SET FOR PRO-C III 26-22 AWG Datasheet资料下载
参数资料
| 型号： | 90758-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET FOR PRO-C III 26-22 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，微型通用 MATE-N-LOK |
| 压接或电缆尺寸： | 22-26 AWG |
| 压接手柄： | A9966-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 425 (CN2011-ZH PDF) |
| 配用： | 170365-4-ND - CONN SOCKET 22-26AWG MINI-UMNL A97678-ND - CONN SOCKET 22-26AWG GOLD CRIMP A97676-ND - CONN PIN 22-26AWG M-U MNL GOLD A33327-ND - CONN PIN 22-26AWG GOLD CRIMP A33328-ND - CONN SOCKET 22-26AWG GOLD CRIMP A32014-ND - CONN SOCKET 22-26AWG GOLD CRIMP A32013-ND - CONN PIN 22-26AWG GOLD CRIMP A28811-ND - CONN SOCKET 22-26AWG GOLD CRIMP A28810-ND - CONN SOCKET 22-26AWG TIN CRIMP A28803-ND - CONN PIN 22-26AWG GOLD CRIMP 更多... |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A30039 |
408-9938
Nut
Locator
Locator Assembly
Tool Frame
Chamfer
Wire Crimper
Offset
Wire Anvil
Insulation
Crimper
Die Retaining Pins
Insulation Anvil
Chamfer
Die Retaining
Screw
Die Retaining
Screw
Figure 2
NOTE
NOTE
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do NOT
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do NOT
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure that
the anvils and crimpers align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvils
and crimpers in place, then tighten both die
retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
Rev D
10. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the four
die retaining pins, and slide the anvils and crimpers
out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
The contact support is preset prior to shipment, but
minor adjustment may be necessary.
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator assembly.
The ratchet has detents that create audible clicks
as the tool handles are closed.
i
3. Place a contact with wire into the proper nest and
close the tool handles until the ratchet reaches the
sixth click, or until the contact support touches the
contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to eliminate
the bending of the contact.
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 90759-2 | DIE SET FOR PRO-C III 22-20,18 |
| 90800-2 | DIE SET HI-DEN D-SUB CRIMP CONT |
| 90869-2 | DIE SET 24-18 AWG USE WITH A9996 |
| 90870-2 | DIE SET FOR PROC III 30-28,26-24 |
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 907-585 | 功能描述:支架与垫片 Plastic Spcr .585 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 907-590 | 功能描述:支架与垫片 Plastic Spcr .59 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90759-1 | 功能描述:折皱器 PROCRIMP W/DIE TOOL MINI UNIV M-N-L RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 90759-2 | 功能描述:冲压机与冲模 DIE 22-18 AWG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 907-595 | 功能描述:支架与垫片 Plastic Spcr .595 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。