- 您现在的位置：买卖IC网 > Datasheet目录612 > 90758-2 (TE Connectivity)DIE SET FOR PRO-C III 26-22 AWG Datasheet资料下载
参数资料
| 型号： | 90758-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | DIE SET FOR PRO-C III 26-22 AWG |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III，微型通用 MATE-N-LOK |
| 压接或电缆尺寸： | 22-26 AWG |
| 压接手柄： | A9966-ND |
| 连接器类型： | 压接端子 |
| 产品目录页面： | 425 (CN2011-ZH PDF) |
| 配用： | 170365-4-ND - CONN SOCKET 22-26AWG MINI-UMNL A97678-ND - CONN SOCKET 22-26AWG GOLD CRIMP A97676-ND - CONN PIN 22-26AWG M-U MNL GOLD A33327-ND - CONN PIN 22-26AWG GOLD CRIMP A33328-ND - CONN SOCKET 22-26AWG GOLD CRIMP A32014-ND - CONN SOCKET 22-26AWG GOLD CRIMP A32013-ND - CONN PIN 22-26AWG GOLD CRIMP A28811-ND - CONN SOCKET 22-26AWG GOLD CRIMP A28810-ND - CONN SOCKET 22-26AWG TIN CRIMP A28803-ND - CONN PIN 22-26AWG GOLD CRIMP 更多... |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A30039 |
408-9938
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp-height comparator. TE does not
manufacture or market crimp-height comparators.
Detailed information on obtaining and using crimp-
height comparators can be found in Instruction Sheet
408-7424.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
Position Point
on Center of
Wire Barrel
Opposite
Screwdriver
Ratchet Adjustment
Wheel
Lockscrew
Figure 5
8. MAINTENANCE
Ensure that the tool frame and dies are clean by
wiping them with a clean, soft cloth. Remove any
debris with a clean, soft brush. Do not use objects that
could damage the tool. When not in use, keep tool
handles closed to prevent objects from becoming
Modified Anvil
“A”
lodged in the dies, and store in a clean, dry area.
9. VISUAL INSPECTION
WIRE SIZE
AWG (Max)
24
18
CRIMP SECTION
(Wire Size
Marking)
26-24
22
CRIMP HEIGHT
DIMENSION “A”
(±0.05 [±.002])
0.69 [.027]
0.79 [.031]
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
See Section 10, REPLACEMENT.
Figure 4
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET (Crimp Height) ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. Using a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a tighter
crimp is required, rotate the adjustment wheel
counterclockwise to a higher-numbered setting. If a
looser crimp is required, rotate the adjustment
wheel clockwise to a lower-numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Rev D
10. REPLACEMENT
Customer-replaceable parts are shown in Figure 1.
Available separately, PRO-CRIMPER III Hand
Crimping Tool Repair Kit 679221-1 includes a
replacement nut and a variety of pins, rings, screws,
and springs. If the dies are damaged or worn
excessively, they must be replaced.
Order the repair kit and replaceable parts through your
TE Representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to
1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
11. REVISION SUMMARY
Revisions to this instruction sheet include:
? Updated document to corporate requirements
? Corrected tooling information in Section 1,
INTRODUCTION
4 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 90759-2 | DIE SET FOR PRO-C III 22-20,18 |
| 90800-2 | DIE SET HI-DEN D-SUB CRIMP CONT |
| 90869-2 | DIE SET 24-18 AWG USE WITH A9996 |
| 90870-2 | DIE SET FOR PROC III 30-28,26-24 |
| 90871-2 | DIE SET 20-14 AWG USE WITH A9996 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 907-585 | 功能描述:支架与垫片 Plastic Spcr .585 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 907-590 | 功能描述:支架与垫片 Plastic Spcr .59 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
| 90759-1 | 功能描述:折皱器 PROCRIMP W/DIE TOOL MINI UNIV M-N-L RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 90759-2 | 功能描述:冲压机与冲模 DIE 22-18 AWG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 907-595 | 功能描述:支架与垫片 Plastic Spcr .595 in Nylon White RoHS:否 制造商:Schurter 类型:Transipillar Spacers 长度:16 m 螺纹大小:M4 外径:10 mm 材料:Nylon with Steel 电镀:Zinc |
发布紧急采购，3分钟左右您将得到回复。