- 您现在的位置：买卖IC网 > Datasheet目录613 > 91963-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 16-14 PIDG Datasheet资料下载
参数资料
| 型号： | 91963-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/7页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 标准包装： | 1 |
| 系列： | * |
5. Insert stripped wire into terminal until wire butts
against locator. Insert stripped wire into splice until
wire butts against the wire stop in splice.
6. Cycle the SDE 1600 Power Unit and hold
momentarily to complete the crimp. The terminal or
splice should be as shown in Figures 5 or 6.
7. Remove the crimped terminal or splice.
8. When crimping a butt splice, reposition the
Tyco Electronics recommends an initial frequency of
once a month, however frequency may be adjusted to
suit your requirements through experience.
Frequency should be dependant on:
Care, amount of handling, and use of the dies;
Type and size of the product being crimped;
Degree of operator skill;
Presence of abnormal amounts of dirt and
dust; and
Your own established standards.
uncrimped half in the stationary die. If the splice
cannot be turned around, turn the tool around, load
the stripped wire in splice and cycle the power unit.
1. Remove dust, moisture, and other contaminants
9. Remove the butt splice.
Each tool has four insulation crimp positions. See
Figure 1.
with a clean, soft brush, or a clean, soft, lint–free
cloth. Do NOT use any objects that could damage
the dies or tool.
2. Make sure that the proper die–retaining screws
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area.
4. Store the tool with the tool handles closed to
prevent objects from becoming lodged within the
jaws.
1. Loosen insulation adjustment locking screw (see
top of tool) and turn indicator to Position 4.
1. Remove dust, moisture, and other contaminants
2. Place terminal or splice in tool dies.
3. Insert UNSTRIPPED wire into ONLY the
with a clean, soft brush, or a clean, soft, lint–free
cloth. Do NOT use any objects that could damage
the dies or tool.
insulation barrel of terminal or splice.
2. Make sure that the proper die–retaining screws
4. Perform a crimp. Remove crimped terminal or
splice and check insulation grip as follows: Bend
the wire back and forth once. Terminal or splice
should retain grip on wire insulation.
5. If wire pulls out, set insulation adjustment
indicator to next tighter position — Position 3.
are properly secured.
3. When the dies are not in use, store them in a
clean, dry area.
4. Store the tool with the tool handles closed to
prevent objects from becoming lodged within the
jaws.
6. Perform a crimp and repeat adjustment as
necessary until desired insulation grip is obtained.
Do not use a tighter setting than required.
1. Remove all lubrication and accumulated film
from the dies by immersing the dies in a suitable
commercial degreaser.
Although the dies are inspected at the factory prior to
their shipment, it is recommended that a maintenance
and inspection program be performed at your facility
periodically. This is necessary to assure that
continued use of the dies will result in the same
dependability and uniform terminations for which the
dies were designed.
2. Make certain that all die–retaining screws and
die components are properly secured.
3. Inspect the crimping surfaces for flattened,
chipped, worn, or cracked areas. If damage is
evident, the dies must be replaced. Refer to
Section 7, REPLACEMENT.
相关PDF资料 |
PDF描述 |
|---|---|
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91-9636-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE 7/0.15 A YELLOW 100M |
| 91963-P2S2 | 制造商:Nuvoton Technology Corp 功能描述:Transformer Toroidal 160VA 2x55V o/p 制造商:NUVOTEM 功能描述:160VA TOROIDAL TX 2X0-55V |
| 919641-000 | 制造商:TE Connectivity 功能描述:101A052-100-0 - Bag 制造商:TE Connectivity 功能描述:BOOT MOLDED |
| 91964-2 | 功能描述:冲压机与冲模 S.D.E.PREM.DIE ASSY 22-16 PIDG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 91-9642-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE A YELLOW 7/0.2MM 25M |
发布紧急采购，3分钟左右您将得到回复。