- 您现在的位置：买卖IC网 > Datasheet目录613 > 91963-2 (TE Connectivity)S.D.E.PREM.DIE ASSY 16-14 PIDG Datasheet资料下载
参数资料
| 型号： | 91963-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 标准包装： | 1 |
| 系列： | * |
3. With wire barrel dies bottomed, inspect the wire
Each tool is inspected for proper die closures before
packaging. An inspection should be performed
periodically to check the tool die closures for
excessive wear.
This inspection requires the use of plug gages
conforming to the dimensions listed in Figure 7. Tyco
Electronics does not manufacture or market these
gages.
To gage the crimping area(s), refer to Figure 8 and
proceed as follows:
1. Clean oil or dirt from the crimping chamber and
plug gage.
2. Cycle the SDE power unit until wire barrel dies
are bottomed. Do not apply additional pressure.
barrel crimping chamber using the proper plug
gage. Lift the spring–loaded locator up and hold
gage in straight alignment with the crimping
chamber. Carefully try to insert, without forcing, the
GO element. See Figure 8. The GO element must
pass completely through the crimping area.
4. Try to insert the NO–GO element. The NO–GO
element may enter partially, but must not pass
completely through the crimping area.
5. Set insulation adjustment indicator in Position 1.
Measure insulation crimping chambers with the
proper GO plug gages in the same manner as
Steps 2 and 3. See Figure 8.
6. With the insulation adjustment indicator in
Position 1, measure the insulation crimping
chambers with the proper NO–GO plug gages. See
Figure 8.
If the crimping areas conform to the gage inspection,
the tool is considered dimensionally correct. If the
crimping areas do not conform to the inspection, the
tool must be repaired. Refer to Section 7,
REPLACEMENT.
Figure 7
GO
NO
GO
相关PDF资料 |
PDF描述 |
|---|---|
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
| 937317-1 | TOOL PUNCH MINI CT PISTOL GRIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91-9636-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE 7/0.15 A YELLOW 100M |
| 91963-P2S2 | 制造商:Nuvoton Technology Corp 功能描述:Transformer Toroidal 160VA 2x55V o/p 制造商:NUVOTEM 功能描述:160VA TOROIDAL TX 2X0-55V |
| 919641-000 | 制造商:TE Connectivity 功能描述:101A052-100-0 - Bag 制造商:TE Connectivity 功能描述:BOOT MOLDED |
| 91964-2 | 功能描述:冲压机与冲模 S.D.E.PREM.DIE ASSY 22-16 PIDG RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 91-9642-27 | 制造商:GLOBAL MEASUREMENT AND CONTROL 功能描述:WIRE PTFE A YELLOW 7/0.2MM 25M |
发布紧急采购，3分钟左右您将得到回复。