- 您现在的位置：买卖IC网 > Datasheet目录306 > A8502KLPTR-T (Allegro Microsystems Inc)IC LED DVR WHITE MULTI 16-TSSOP Datasheet资料下载
参数资料
| 型号： | A8502KLPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 28/35页 |
| 文件大小： | 0K |
| 描述： | IC LED DVR WHITE MULTI 16-TSSOP |
| 标准包装： | 8,000 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 2 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 580kHz ~ 2MHz |
| 电源电压： | 5 V ~ 40 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页
A8502
Wide Input Voltage Range, High Efficiency
Fault Tolerant LED Driver
The reverse voltage rating should be such that during operation
condition, the voltage rating of the device is larger than the maxi-
The rms current through the capacitor is given by:
? I Lused
I IN (max) × 12
0.72 +
0.94 (A) × 12
= 0.240 (A)
mum output voltage. In this case it isV OUT(OVP) .
The peak current through the diode is calculated as:
I dp = I IN (max) + 1 / 2 Δ I Lused (23)
= 0.94 (A) + 0.36 (A) / 2 = 1.12 A
The third major component in deciding the switching diode is the
reverse current, I R , characteristic of the diode. This characteristic
is especially important when PWM dimming is implemented.
I COUT rms = I OUT
D (max) +
1 – D (max)
0.36 (A)
1 – 0.72
= 0.39 A
(25)
During PWM off-time the boost converter is not switching. This
results in a slow bleeding off of the output voltage, due to leakage
currents. I R can be a large contributor, especially at high tempera-
tures. On the diode that was selected in this design, the current
varies between 1 and 100 μ A.
Step 7 Choosing the output capacitors. The output capacitors
must be chosen such that they can provide filtering for both the
boost converter and for the PWM dimming function. The biggest
The output capacitor must have a current rating of at least
390 mA. The capacitor selected in this design was a 4.7 μ F 50 V
capacitor with a 3 A current rating.
Step 8 Selecting input capacitor. The input capacitor must be
selected such that it provides a good filtering of the input voltage
waveform. A good estimation rule is to set the input voltage rip-
ple, Δ V IN , to be 1% of the minimum input voltage. The minimum
input capacitor requirements are as follows:
factors that contribute to the size of the output capacitor are:
PWM dimming frequency and PWM duty cycle. Another major
contributor is leakage current, I LK . This current is the combina-
tion of the OVP leakage current as well as the reverse current of
the switching diode. In this design the PWM dimming frequency
C IN =
=
8
8
? I Lused
f SW ? V IN
0.36 (A)
2 (MHz) 0.1 (V)
= 0.23 μ F
(26)
is 200 Hz and the minimum duty cycle is 1%. Typically, the volt-
1 – D (min)
C OUT = I LK
f PWM(dimming)
= 200 ( μ A)
= 3.96 μ F
I OUT ×
C IN rms =
0.240 (A) ×
age variation on the output,V COUT , during PWM dimming must
be less than 250 mV, so that no audible hum can be heard. The
capacitance can be calculated as follows:
(24)
V COUT
1 – 0.01
200 (Hz) 0.250 (V)
A capacitor larger than 3.96 μ F should be selected due to degra-
The rms current through the capacitor is given by:
? I Lused
I IN (max)
(1 – D )× 12
0.36 (A)
0.94 (A)
= = 0.095 A
(1 – 0.72)× 12
(27)
dation of capacitance at high voltages on the capacitor. A ceramic
4.7 μ F 50 V capacitor is a good choice to fulfill this requirement.
Corresponding capacitors include:
A good ceramic input capacitor with ratings of 2.2 μ F 50 V or
4.7 μ F 50 V will suffice for this application. Corresponding
capacitors include:
Vendor
Murata
Murata
Value
4.7 μ F 50 V
2.2 μ F 50 V
Part number
GRM32ER71H475KA88L
GRM31CR71H225KA88L
Vendor
Murata
Murata
Value
4.7 μ F 50 V
2.2 μ F 50 V
Part number
GRM32ER71H475KA88L
GRM31CR71H225KA88L
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
28
相关PDF资料 |
PDF描述 |
|---|---|
| A8504EECTR-T | IC LED DRVR WHT/RGB BCKLGT 26QFN |
| A8507ELBTR-T | IC DRIVER WLED/RGB 24-SOIC |
| A8508GLPTR-T | IC LED DVR WHITE 8X120MA 24TSSOP |
| A8509GLPTR-T | IC LED DVR WHITE 4X120MA 24TSSOP |
| A8510GECTR-T | IC LED DRVR BCKLGHT/WHT 26QFN-EC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8503 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:High Efficiency 6-Channel, 2 MHz, WLED/RGB Driver |
| A8503EECTR-T | 功能描述:IC LED DRVR WHT/RGB BCKLGT 26QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:1 系列:- 恒定电流:- 恒定电压:- 拓扑:PWM，切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:642kHz 电源电压:2.7 V ~ 5.5 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘 供应商设备封装:10-VSON 包装:剪切带 (CT) 工作温度:-30°C ~ 85°C 产品目录页面:1371 (CN2011-ZH PDF) 其它名称:BD1603NUV-E2CT |
| A8503GECTR-T | 功能描述:IC LED DVR WHT/RGB BKLGT 26QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| A8504 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:WLED/RGB Backlight Driver for Medium Size LCDs |
| A8504910100N | 功能描述:环形MIL规格后盖 Backshell, Envrn, EMI/RFI, Strt, Nickel, Size 48 RoHS:否 制造商:Amphenol PCD MIL 类型:MIL-DTL-38999 III, IV 系列:AS85049 产品类型:Environmental EMI/RFI Backshells 外壳类型:Straight 外壳大小:18 外壳材质:Aluminum Alloy |
发布紧急采购，3分钟左右您将得到回复。