- 您现在的位置：买卖IC网 > Datasheet目录307 > A8510GECTR-T (Allegro Microsystems Inc)IC LED DRVR BCKLGHT/WHT 26QFN-EC Datasheet资料下载
参数资料
| 型号： | A8510GECTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR BCKLGHT/WHT 26QFN-EC |
| 标准包装： | 1 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 8 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 600kHz ~ 2.25MHz |
| 电源电压： | 5 V ~ 40 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 26-WFQFN 裸露焊盘 |
| 供应商设备封装： | 26-QFN/MLP-EP（4x4） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 105°C |
| 其它名称： | 620-1385-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
A8510
Design Example for Boost Configuration
Wide Input Voltage Range, High Efficiency
Fault Tolerant LED Driver
Applications Information
Then the OVP resistor is:
This section provides a method for selecting component values
R OVP = ( V OUT(OVP) – V OVP(th) ) / I OVPH
(8)
when designing an application using the A8510. An example
schematic is provided in figure 30.
Assumptions: For the purposes of this example, the following are
given as the application requirements:
? V BAT : 10 to 14 V
? Quantity of LED channels, # CHANNELS : 8
? Quantity of series LEDs per channel, # SERIESLEDS : 12
? LED current per channel, I LED : 40 mA
? V f at 40 mA: 3.2 V
? f SW : 800 kHz
? T A (max): 65°C
? PWM dimming frequency: 200 Hz, 1% Duty cycle
= (41.08 V – 8.1 V) / 199 μ A = 165.73 k Ω
where both I OVPH and V OVP(th) are taken from the Electrical
Characteristics table.
Chose a value of resistor that is higher value than the calculated
R OVP . In this case a value of 169 k Ω was selected. Below is the
actual value of the minimum OVP trip level with the selected
resistor:
V OUT(OVP) = 169 k Ω × 199 μ A + 8.1 V = 41.7 V
Step 3b At this point a quick check must be done to see if the
conversion ratio is acceptable for the selected frequency.
Procedure: The procedure consists of selecting the appropriate
configuration and then the individual component values, in an
D maxofboost = 1 – t SWOFFTIME × f SW
(9)
ordered sequence. It should be noted that in many calculations
the minimum and/or maximum specification values are used to
guarantee proper system operation.
Step 1 Connect LEDs to pins LED1 through LED8.
Step 2 Determining the LED current setting resistor R ISET :
= 1 – 1.5 × 47 ns × 800 kHz = 94.36%
where minimum off time (t SWOFFTIME ) is found in the Electrical
Characteristics table.
The Theoretical Maximum V OUT is then calculated as:
R ISET = 1.003 × 327 / I LED
= 327.981 / 40 mA = 8.20 k Ω
(6)
V OUTthe (max) =
V IN (min)
1 – D maxofboost
– V d
(10)
– 0.4 = 177 V
=
Choose a 8.25 kΩ resistor.
Step 3 Determining the OVP resistor. The OVP resistor is
connected between the OVP pin and the output voltage of the
converter.
Step 3a The first step is determining the maximum voltage
based on the LED requirements. Then this value and the regula-
tion voltage (V LED ) should be added together, as well as another
750 mV to take noise and output ripple into consideration. The
regulation voltage, V LED , of the A8510 is 680 mV.
10 V
1 – 0.9436
where V d is the diode forward voltage.
The Theoretical Maximum V OUT value must be greater than the
value V OUT(OVP) . If this is not the case, the switching frequency
of the boost converter must be reduced to meet the maximum
duty cycle requirements.
Step 4 Selecting the inductor. The inductor must be chosen such
V OUT(OVP) = # SERIESLEDS × V f + V LED + 2
= 12 × 3.2 V+ 0.680 V + 2 V
= 41.08 V
(7)
that it can handle the necessary input current. In most applica-
tions, due to stringent EMI requirements, the system must operate
in continuous conduction mode throughout the whole input volt-
age range.
24
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A8511KLPTR-T | IC LED DVR 150MA AUTO 28-TSSOP |
| A8512ELBTR-T | IC LED DVR WHT/RGB BKLGT 24SOIC |
| A8513KLPTR-T | IC LED DRVR AUTO BCKLGHT 16TSSOP |
| A8514KLPTR-T | IC LED DVR WHT 4X80MA 16-ETSSOP |
| A8515GLPTR-T | IC LED DVR WHT/RGB BKLGT 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A8511 | 制造商:ROCKWE 功能描述: |
| A8511KLPTR-T | 功能描述:IC LED DVR 150MA AUTO 28-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 特色产品:LM3445 TRIAC Dimmable LED Driver 标准包装:55 系列:PowerWise® 恒定电流:是 恒定电压:- 拓扑:PWM，降压（降压） 输出数:1 内部驱动器:无 类型 - 主要:- 类型 - 次要:高亮度 LED（HBLED） 频率:30kHz ~ 1MHz 电源电压:8 V ~ 12 V 输出电压:- 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:管件 工作温度:-40°C ~ 125°C 产品目录页面:1285 (CN2011-ZH PDF) 其它名称:LM3445M |
| A8512 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:LED Backlight Driver for Medium/Large Displays |
| A8512EETTR-T | 功能描述:IC LED DVR WHT/RGB BKLGT 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
| A8512ELBTR-T | 功能描述:IC LED DVR WHT/RGB BKLGT 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 恒定电流:- 恒定电压:- 拓扑:升压（升压），切换式电容器（充电泵） 输出数:1 内部驱动器:是 类型 - 主要:背光 类型 - 次要:白色 LED 频率:625kHz ~ 875kHz 电源电压:2.7 V ~ 5.3 V 输出电压:5V 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) 工作温度:-40°C ~ 85°C |
发布紧急采购，3分钟左右您将得到回复。