- 您现在的位置：买卖IC网 > PDF目录9310 > AD5161BRM5-RL7 (Analog Devices Inc)IC DGTL POT SPI 256POS 10-MSOP PDF资料下载
参数资料
| 型号： | AD5161BRM5-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT SPI 256POS 10-MSOP |
| 标准包装： | 1,000 |
| 接片： | 256 |
| 电阻（欧姆）： | 5k |
| 电路数： | 1 |
| 温度系数： | 标准值 45 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C，SPI |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
Data Sheet
AD5161
Rev. B | Page 15 of 20
THEORY OF OPERATION
The AD5161 is a 256-position digitally controlled variable
resistor (VR)1 device.
An internal power-on preset places the wiper at midscale during
power-on, which simplifies the fault condition recovery at power-up.
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between terminals A and
B is available in 5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ. The final two
or three digits of the part number determine the nominal resistance
value, e.g., 10 kΩ = 10; 50 kΩ = 50. The nominal resistance (RAB) of
the VR has 256 contact points accessed by the wiper terminal,
plus the B terminal contact. The 8-bit data in the RDAC latch is
decoded to select one of the 256 possible settings. Assume a 10 kΩ
part is used, the wiper’s first connection starts at the B terminal
for data 0x00. Since there is a 60 Ω wiper contact resistance, such
connection yields a minimum of 60 Ω resistance between
Terminals W and B. The second connection is the first tap point,
which corresponds to 99 Ω (RWB = RAB/256 + RW = 39 Ω + 60 Ω)
for data 0x01. The third connection is the next tap point,
representing 177 Ω (2 × 39 Ω + 60 Ω) for data 0x02 and so on. Each
LSB data value increase moves the wiper up the resistor ladder
until the last tap point is reached at 9961 Ω (RAB – 1 LSB + RW).
Figure 42 shows a simplified diagram of the equivalent RDAC
circuit where the last resistor string will not be accessed;
therefore, there is 1 LSB less of the nominal resistance at full
scale in addition to the wiper resistance.
B
RDAC
LATCH
AND
DECODER
W
A
RS
SD BIT
D7
D6
D4
D5
D2
D3
D1
D0
Figure 42. AD5161 Equivalent RDAC Circuit
1 The terms digital potentiometer, VR, and RDAC are used interchangeably.
The general equation determining the digitally programmed
output resistance between W and B is
W
AB
WB
R
D
R
256
)
(
(1)
where D is the decimal equivalent of the binary code loaded in
the 8-bit RDAC register, RAB is the end-to-end resistance, and
RW
is the wiper resistance contributed by the on resistance of
the internal switch.
In summary, if RAB = 10 kΩ and the A terminal is open circuited,
the following output resistance RWB will be set for the indicated
RDAC latch codes.
Table 9. Codes and Corresponding RWB Resistance
D (Dec.)
RWB (Ω)
Output State
255
9,961
Full Scale (RAB – 1 LSB + RW)
128
5,060
Midscale
1
99
1 LSB
0
60
Zero Scale (Wiper Contact Resistance)
Note that in the zero-scale condition a finite wiper resistance of
60 Ω is present. Care should be taken to limit the current flow
between W and B in this state to a maximum pulse current of
no more than 20 mA. Otherwise, degradation or possible
destruction of the internal switch contact can occur.
Similar to the mechanical potentiometer, the resistance of the
RDAC between the wiper W and terminal A also produces a
digitally controlled complementary resistance RWA. When these
terminals are used, the B terminal can be opened. Setting the
resistance value for RWA starts at a maximum value of resistance
and decreases as the data loaded in the latch increases in value.
The general equation for this operation is
W
AB
WA
R
D
R
256
)
(
(2)
For RAB = 10 kΩ and the B terminal open circuited, the
following output resistance RWA will be set for the indicated
RDAC latch codes.
Table 10. Codes and Corresponding RWA Resistance
D (Dec.)
RWA (Ω)
Output State
255
99
Full Scale
128
5,060
Midscale
1
9,961
1 LSB
0
10,060
Zero Scale
Typical device to device matching is process lot dependent and
may vary by up to ±30%. Since the resistance element is processed
in thin film technology, the change in RAB with temperature has
a very low 45 ppm/°C temperature coefficient.
相关PDF资料 |
PDF描述 |
|---|---|
| DS14285S+T&R | IC RTC W/NV RAM CNTRL 24-SOIC |
| DS14285S+ | IC RTC W/NV RAM CNTRL 24-SOIC |
| AD5161BRM100-RL7 | IC DGTL POT SPI 256POS 10-MSOP |
| VE-B6P-IU-F4 | CONVERTER MOD DC/DC 13.8V 200W |
| VE-BWM-MW-B1 | CONVERTER MOD DC/DC 10V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5161BRMZ10 | 功能描述:IC DGTL POT SPI 10K 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5161BRMZ10 | 制造商:Analog Devices 功能描述:IC 8-BIT DIGITAL POT |
| AD5161BRMZ100 | 功能描述:IC DGTL POT SPI 100K 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,300 系列:WiperLock™ 接片:257 电阻（欧姆）:100k 电路数:1 温度系数:标准值 150 ppm/°C 存储器类型:易失 接口:3 线 SPI（芯片选择） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VDFN 裸露焊盘 供应商设备封装:8-DFN-EP（3x3） 包装:带卷 (TR) |
| AD5161BRMZ100-RL7 | 功能描述:IC DGTL POT SPI 100K 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
| AD5161BRMZ10-RL7 | 功能描述:IC DGTL POT SPI 10K 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。