参数资料
| 型号： | AD5231BRU50 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 1024POS 16-TSSOP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 标准包装： | 96 |
| 接片： | 1024 |
| 电阻（欧姆）： | 50k |
| 电路数： | 1 |
| 温度系数： | 标准值 600 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V，±2.25 V ~ 2.75 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD5231
Rev. D | Page 19 of 28
Using Additional Internal Nonvolatile EEMEM
The AD5231 contains additional user EEMEM registers for
storing any 16-bit data such as memory data for other compo-
nents, look-up tables, or system identification information.
Table 9 provides an address map of the internal storage registers
shown in the functional block diagram as EEMEM1, EEMEM2,
and 28 bytes (14 addresses × 2 bytes each) of user EEMEM.
Table 9. EEMEM Address Map
Address
EEMEM for…
0000
RDAC1, 2
0001
O1 and O23
0010
USER14
0011
USER2
…
1110
USER13
1111
USER14
1
RDAC data stored in EEMEM location is transferred to the RDAC register at
power-on, or when Instruction 1, Instruction 8, or PR are executed.
2
Execution of Instruction 1 leaves the device in the read mode power
consumption state. After the last Instruction 1 is executed, the user should
perform a NOP, Instruction 0 to return the device to the low power idling
state.
3
O1 and O2 data stored in EEMEM locations is transferred to the
corresponding digital register at power-on, or when Instruction 1 and
Instruction 8 are executed.
4
USERx are internal nonvolatile EEMEM registers available to store 16-bit
information using Instruction 3 and restore the contents using Instruction 9.
RDAC STRUCTURE
The patent-pending RDAC contains multiple strings of equal
resistor segments with an array of analog switches that act as the
wiper connection. The number of positions is the resolution of
the device. The AD5231 has 1024 connection points, allowing it
to provide better than 0.1% settability resolution. Figure 43
shows an equivalent structure of the connections among the
three terminals of the RDAC. The SWA and SWB are always on,
while the switches SW(0) to SW(2N1) are on one at a time,
depending on the resistance position decoded from the data
bits. Because the switch is not ideal, there is a 15 wiper
resistance, RW. Wiper resistance is a function of supply voltage
and temperature. The lower the supply voltage or the higher the
temperature, the higher the resulting wiper resistance. Users
should be aware of the wiper resistance dynamics if accurate
prediction of the output resistance is needed.
SW(1)
SW(0)
SWB
B
SWA
SW(2N–1)
SW(2N–2)
A
W
RS
RS = RAB/2N
DIGITAL
CIRCUITRY
OMITTED FOR
CLARITY
RDAC
WIPER
REGISTER
AND
DECODER
02739-
042
Figure 43. Equivalent RDAC Structure (Patent Pending)
Table 10. Nominal Individual Segment Resistor (RS)
Device
Resolution
10 k
Version
50 k
Version
100 k
Version
10-Bit
9.8
48.8
97.6
PROGRAMMING THE VARIABLE RESISTOR
Rheostat Operation
The nominal resistance of the RDAC between Terminal A and
Terminal B, RAB, is available with 10 k, 50 k, and 100 k
with 1024 positions (10-bit resolution). The final digit(s) of the
part number determine the nominal resistance value, for
example, 10 k = 10; 50 k = 50; 100 k = C.
The 10-bit data-word in the RDAC latch is decoded to select
one of the 1024 possible settings. The following discussion
describes the calculation of resistance RWB at different codes of a
10 k part. For VDD = 5 V, the wiper’s first connection starts at
Terminal B for data 0x000. RWB(0) is 15 because of the wiper
resistance, and because it is independent of the nominal
resistance. The second connection is the first tap point where
RWB (1) becomes 9.7 + 15 = 24.7 for data 0x001. The
third connection is the next tap point representing RWB (2) =
19.4 + 15 = 34.4 for data 0x002 and so on. Each LSB data
value increase moves the wiper up the resistor ladder until the
for a simplified diagram of the equivalent RDAC circuit. When
RWB is used, Terminal A can be left floating or tied to the wiper.
相关PDF资料 |
PDF描述 |
|---|---|
| GTC06F-22-22P | CONN PLUG 4POS STRAIGHT W/PINS |
| AD5220BRMZ50-RL7 | IC DGTL POT SNGL 128POS 8USOIC |
| VE-22Y-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| AD5220BR100 | IC DGTL POT SNGL 128POS 8-SOIC |
| 74VHC138SJX | DECODER/DEMUX 3-TO-8 16SOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5231BRU50-REEL7 | 功能描述:IC DGTL POT 1024POS 16-TSSOP TR RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:2,500 系列:XDCP™ 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 ±300 ppm/°C 存储器类型:非易失 接口:I²C（设备位址） 电源电压:2.7 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:14-TSSOP 包装:带卷 (TR) |
| AD5231BRUZ10 | 功能描述:IC POT DGTL 1024POS 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5231BRUZ10 | 制造商:Analog Devices 功能描述:Digital Potentiometer (Pots) IC |
| AD5231BRUZ100 | 功能描述:IC DGTL POT 100K SPI 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 接片:256 电阻（欧姆）:100k 电路数:1 温度系数:标准值 35 ppm/°C 存储器类型:非易失 接口:3 线串口 电源电压:2.7 V ~ 5.25 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WDFN 裸露焊盘 供应商设备封装:8-TDFN-EP（3x3） 包装:剪切带 (CT) 产品目录页面:1399 (CN2011-ZH PDF) 其它名称:MAX5423ETA+TCT |
| AD5231BRUZ100-RL7 | 功能描述:IC DGTL POT 100K 16-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数字电位器 系列:- 标准包装:3,000 系列:DPP 接片:32 电阻（欧姆）:10k 电路数:1 温度系数:标准值 300 ppm/°C 存储器类型:非易失 接口:3 线串行（芯片选择，递增，增/减） 电源电压:2.5 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-WFDFN 裸露焊盘 供应商设备封装:8-TDFN（2x3） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。