- 您现在的位置：买卖IC网 > PDF目录10532 > AD670JNZ (Analog Devices Inc)IC ADC 8BIT SGNL COND 20-DIP PDF资料下载
参数资料
| 型号： | AD670JNZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT SGNL COND 20-DIP |
| 标准包装： | 18 |
| 位数： | 8 |
| 采样率（每秒）： | 10k |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 450mW |
| 电压电源： | 单电源 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
| 产品目录页面： | 777 (CN2011-ZH PDF) |
AD670
REV. A
–9–
APPLYING THE AD670
The AD670 has been designed for ease of use, system compat-
ibility, and minimization of external components. Transducer
interfaces generally require signal conditioning and preampli-
fication before the signal can be converted. The AD670 will
reduce and even eliminate this excess circuitry in many cases.
To illustrate the flexibility and superior solution that the AD670
can bring to a transducer interface problem, the following dis-
cussions are offered.
Temperature Measurements
Temperature transducers are one of the most common sources
of analog signals in data acquisition systems. These sensors re-
quire circuitry for excitation and preamplification/buffering. The
instrumentation amplifier input of the AD670 eliminates the
need for this signal conditioning. The output signals from tem-
perature transducers are generally sufficiency slow that a
sample/hold amplifier is not required. Figure 12 shows tile
AD590 IC temperature transducer interfaced to the AD670.
The AD580 voltage reference is used to offset the input for 0
°C
calibration. The current output of the AD590 is converted into
a voltage by R1. The high impedance unbuffered voltage is ap-
plied directly to the AD670 configured in the –128 mV to
127 mV bipolar range. The digital output will have a resolution
of 1
°C.
Figure 12. AD670 Temperature Transducer lnterface
Platinum RTDs are also a popular, temperature transducer.
Typical RTDs have a resistance of 100
at 0°C and change re-
sistance 0.4
per °C. If a consent excitation current is caused
to flow in the RTD, the change in voltage drop will be a mea-
sure of the change in temperature. Figure 13 shows such a
method and the required connections to the AD670. The
AD580 2.5 V reference provides the accurate voltage for the ex-
citation current and range offsetting for the RTD. The op amp
is configured to force a constant 2.5 mA current through the
RTD. The differential inputs of the AD670 measure the differ-
ence between a fixed offset voltage and the temperature depen-
dent output of the op amp which varies with the resistance of
the RTD. The RTD change of approximately 0.4
/°C results
in a 1 mV/
°C voltage change. With the AD670 in the 1 mV/LSB
range, temperatures from 0
°C to 255°C can be measured.
Figure 13. Low Cost RTD Interface
Differential temperature measurements can be made using an
AD590 connected to each of the inputs as shown in Figure 14.
This configuration will allow the user to measure the relative
temperature difference between two points with a 1
°C resolu-
tion. Although the internal 1k and 9k resistors on the inputs
have
±20% tolerance, trimming the AD590 is unnecessary as
most differential temperature applications are concerned with
the relative differences between the two. However, the user may
see up to a 20% scale factor error in the differential temperature
to digital output transfer curve.
This scale factor error can be eliminated through a software cor-
rection. Offset corrections can be made by adjusting for any dif-
ference that results when both sensors are held at the same
temperature. A span adjustment can then be made by immers-
ing one AD590 in an ice bath and one in boiling water and
eliminating any deviation from 100
°C. For a low cost version of
this setup, the plastic AD592 can be substituted for the AD590.
Figure 14. Differential Temperature Measurement
Using the AD590
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4W-MY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
| VI-B4V-MX-F2 | CONVERTER MOD DC/DC 5.8V 75W |
| LTC2291CUP#PBF | IC ADC DUAL 12BIT 25MSPS 64QFN |
| VI-B4V-MX-F1 | CONVERTER MOD DC/DC 5.8V 75W |
| VE-J4V-MY-F2 | CONVERTER MOD DC/DC 5.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD670JNZ | 制造商:Analog Devices 功能描述:IC 8-BIT ADC |
| AD670JP | 功能描述:IC ADC 8BIT SGNL COND 20-PLCC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD670JP-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PLCC T/R |
| AD670JP-REEL7 | 制造商:Analog Devices 功能描述: |
| AD670JPZ | 功能描述:IC ADC 8BIT SIGNAL COND 20-PLCC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。