- 您现在的位置：买卖IC网 > PDF目录1980 > AD7329BRUZ-REEL7 (Analog Devices Inc)IC ADC 12BIT+SAR 8CHAN 24-TSSOP PDF资料下载
参数资料
| 型号： | AD7329BRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/41页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT+SAR 8CHAN 24-TSSOP |
| 标准包装： | 1,000 |
| 位数： | 12 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 30mW |
| 电压电源： | 双 ± |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；8 个单端，双极；4 个差分，单极；4 个差分，双极 |
| 配用： | EVAL-AD7329CBZ-ND - BOARD EVALUATION FOR AD7329CBZ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
Data Sheet
AD7329
Rev. B | Page 37 of 40
APPLICATIONS INFORMATION
LAYOUT AND GROUNDING
The printed circuit board that houses the AD7329 should be
designed so that the analog and digital sections are confined to
certain areas of the board. This design facilitates the use of ground
planes that can be easily separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally best. All AGND pins on the AD7329
should be connected to the AGND plane. Digital and analog
ground pins should be joined in only one place. If the AD7329
is in a system where multiple devices require an AGND and
DGND connection, the connection should still be made at only
one point. A star point should be established as close as possible
to the ground pins on the AD7329.
Good connections should be made to the power and ground
planes. This can be done with a single via or multiple vias for
each supply and ground pin.
Avoid running digital lines under the AD7329 device because
this couples noise onto the die. However, the analog ground
plane should be allowed to run under the AD7329 to avoid
noise coupling. The power supply lines to the AD7329 device
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
To avoid radiating noise to other sections of the board, com-
ponents, such as clocks, with fast switching signals should be
shielded with digital ground and never run near the analog inputs.
Avoid crossover of digital and analog signals. To reduce the effects
of feedthrough within the board, traces should be run at right
angles to each other. A microstrip technique is the best method,
but its use may not be possible with a double-sided board. In
this technique, the component side of the board is dedicated to
ground planes, and signals are placed on the other side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 F tantalum capacitors in parallel with
0.1 F capacitors to AGND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 F capacitors should have a low effective series resistance
(ESR) and low effective series inductance (ESI), such as is typical
of common ceramic and surface-mount types of capacitors.
These low ESR, low ESI capacitors provide a low impedance
path to ground at high frequencies to handle transient currents
due to internal logic switching.
POWER SUPPLY CONFIGURATION
It is recommended that Schottky diodes be placed in series with
Schottky diode configuration. BAT43 Schottky diodes are used.
05402-
060
VIN0
VIN7
CS
SCLK
DOUT
DIN
VDD
VCC
VSS
AD73291
V–
V+
3V/5V
1ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 60. Schottky Diode Connection
In an application where nonsymmetrical VDD and VSS supplies
are used, adhere to the guidelines provided in Table 18, which
outlines the VSS supply range that can be used for various VDD
voltages when nonsymmetrical supplies are required. When
recommended that these supplies be symmetrical.
Table 18. Nonsymmetrical VDD and VSS Requirements
VDD
Typical VSS Range
5 V
5 V to 5.5 V
6 V
5 V to 8.5 V
7 V
5 V to 11.5 V
8 V
5 V to 15 V
9 V
5 V to 16.5 V
10 V to 16.5 V
5 V to 16.5 V
For the 0 V to 4 × VREF range, VSS can be tied to AGND as per
the minimum supply recommendations outlined in Table 6.
相关PDF资料 |
PDF描述 |
|---|---|
| AD73311ARSZ | IC ANALOG FRONT END 20-SSOP |
| AD73322LARUZ-REEL | IC PROCESSOR FRONTEND DL 28TSSOP |
| AD73322LYRZ | IC ANALOG FRONT END DUAL 28-SOIC |
| AD73360ARZ | IC PROCESSOR FRONTEND 6CH 28SOIC |
| AD7352YRUZ-500RL7 | IC ADC DUAL 12BIT 3MSPS 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD73311 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End |
| AD73311AR | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:SPEECH & TELEPHONY CODEC I.C. - Bulk 制造商:Analog Devices 功能描述:SPEECH/TELEPHONY CODEC SMD 73311 |
| AD73311AR-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R |
| AD73311ARS | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP |
| AD73311ARS-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP T/R 制造商:Rochester Electronics LLC 功能描述:SPEECH & TELEPHONY CODEC I.C. - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。