收藏本站
参数资料
型号： AD7658BSTZ
厂商： Analog Devices Inc
文件页数： 17/32页
文件大小： 0K
描述： IC ADC 12BIT 6CH 250KSPS 64LQFP
标准包装： 1
位数： 12
采样率（每秒）： 250k
数据接口： 串行，并联
转换器数目： 6
功率耗散（最大）： 143mW
电压电源： 模拟和数字，双 ±
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 64-LQFP
供应商设备封装： 64-LQFP（10x10）
包装： 托盘
输入数目和类型： 6 个单端，双极
产品目录页面： 778 (CN2011-ZH PDF)
配用： EVAL-AD7658CBZ-ND - BOARD EVAL FOR AD7658
AD7656/AD7657/AD7658
Data Sheet
Rev. D | Page 24 of 32
Software Selection of ADCs
The H/S SEL pin determines the source of the combination of
ADCs that are to be simultaneously sampled. When the H/S SEL
pin is logic low, the combination of channels to be simultaneously
sampled is determined by the CONVST A, CONVST B, and
CONVST C pins. When the H/S SEL pin is logic high, the
combination of channels selected for simultaneous sampling is
determined by the contents of the Control Register DB15 to
Control Register DB13. In this mode, a write to the control
register is necessary.
The control register is an 8-bit write-only register. Data is written
to this register using the CS and WR pins and the DB[15:8] data
pins (see Figure 29). The control register is shown in Table 10.
To select an ADC pair to be simultaneously sampled, set the
corresponding data line high during the write operation.
The AD7656/AD7657/AD7658 control register allows
individual ranges to be programmed on each ADC pair.
DB12 to DB10 in the control register are used to program
the range on each ADC pair.
After a reset occurs on the AD7656/AD7657/AD7658, the
control register contains all zeros.
The CONVST A signal is used to initiate a simultaneous
conversion on the combination of channels selected via the
control register. The CONVST B and CONVST C signals can
be tied low when operating in software mode (H/S SEL = 1).
The number of read pulses required depends on the number
of ADCs selected in the control register and on whether the
devices are operating in word or byte mode. The conversion
results are output in ascending order.
During the write operation, Data Bus Bit DB15 to Bit DB8 are
bidirectional and become inputs to the control register when
RD is logic high and CS and WR are logic low. The logic state
on DB15 through DB8 is latched into the control register when
WR goes logic high.
Table 10. Control Register Bit Function Descriptions
(Default All 0s)
DB15
DB14
DB13
DB12
DB11
DB10
DB9
DB8
VC
VB
VA
RNGC
RNGB
RNGA
REFEN
REFBUF
Table 11.
Bit
Mnemonic
Comment
DB15
VC
This bit is used to select Analog Inputs V5
and V6 for the next conversion.
When this bit = 1, V5 and V6 are
simultaneously converted on the
next CONVST A rising edge.
DB14
VB
This bit is used to select Analog Inputs
V3 and V4 for the next conversion.
When this bit = 1, V3 and V4 are
simultaneously converted on the
next CONVST A rising edge.
DB13
VA
This bit is used to select Analog Inputs
V1 and V2 for the next conversion.
When this bit = 1, V1 and V2 are
simultaneously converted on the
next CONVST A rising edge.
DB12
RNGC
This bit is used to select the analog input
range for Analog Inputs V5 and V6.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
DB11
RNGB
This bit is used to select the analog input
range for Analog Inputs V3 and V4.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
DB10
RNGA
This bit is used to select the analog input
range for Analog Inputs V1 and V2.
When this bit = 1, the ±2 × VREF mode is
selected for the next conversion.
When this bit = 0, the ±4 × VREF mode is
selected for the next conversion.
DB9
REFEN
This bit is used to select the internal
reference or an external reference.
When this bit = 0, the external reference
mode is selected. When this bit = 1, the
internal reference is selected.
DB8
REFBUF
This bit is used to select between using the
internal reference buffers and choosing
to bypass these reference buffers.
When this bit = 0, the internal reference
buffers are enabled and decoupling is
required on the REFCAP pins. When this
bit = 1, the internal reference buffers are
disabled and a buffered reference should
be applied to the REFCAP pins.
DATA
DB15 TO DB8
CS
t13
t15
t14
t11
t12
WR
05020-
009
Figure 29. Parallel Interface—Write Cycle for Word Mode (W/B= 0)
相关PDF资料
PDF描述
AD7767BRUZ-1 ADC 24BIT 64KSPS SAR 16-TSSOP
AD7714YRUZ IC ADC SIGNAL COND 3/5V 24-TSSOP
LTC2446IUHF#PBF IC ADC 24BIT 8CH HI SPEED 38QFN
LTC2448IUHF#PBF IC ADC 24BIT HI SPEED 38QFN
LTC2447IUHF#PBF IC ADC 24BIT 8CH HI SPEED 38QFN
相关代理商/技术参数
参数描述
AD7658BSTZ-1 功能描述:IC ADC 12BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6
AD7658BSTZ-1-RL 功能描述:IC ADC 12BIT 6CH 250KSPS 64LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
AD7658BSTZ-REEL 功能描述:IC ADC 12BIT 6CH 250KSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
AD7658BSTZ-U3 制造商:Analog Devices 功能描述:ADC HEX SAR 250KSPS 12-BIT PARALLEL/SERL 64LQFP - Rail/Tube
AD7658YSTZ 功能描述:IC ADC 12BIT 6CH 250KSPS 64-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*