- 您现在的位置：买卖IC网 > PDF目录10064 > AD7711AQ (Analog Devices Inc)IC ADC 24BIT RTD I SOURCE 24CDIP PDF资料下载
参数资料
| 型号： | AD7711AQ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT RTD I SOURCE 24CDIP |
| 标准包装： | 15 |
| 位数： | 24 |
| 采样率（每秒）： | 1.03k |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 52.5mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 80°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 24-CDIP（0.300"，7.62mm） |
| 供应商设备封装： | 24-CDIP |
| 包装： | 管件 |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极；1 个差分，单极；1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
2
REV.G
AD7711
–19–
Measurement errors due to offset drift or gain drift can be elimi-
nated at any time by recalibrating the converter or by operating
the part in the background calibration mode. Using the system
calibration mode can also minimize offset and gain errors in the
signal conditioning circuitry. Integral and differential linearity
errors are not significantly affected by temperature changes.
POWER SUPPLIES AND GROUNDING
Because the analog inputs and reference input are differential,
most of the voltages in the analog modulator are common-mode
voltages. VBIAS provides the return path for most of the analog
currents flowing in the analog modulator. As a result, the VBIAS
input should be driven from a low impedance to minimize errors
due to charging/discharging impedances on this line. When the
internal reference is used as the reference source for the part,
AGND is the ground return for this reference voltage.
The analog and digital supplies to the AD7711 are independent
and separately pinned out to minimize coupling between the
analog and digital sections of the device. The digital filter will
provide rejection of broadband noise on the power supplies,
except at integer multiples of the modulator sampling frequency.
The digital supply (DVDD) must not exceed the analog positive
supply (AVDD) by more than 0.3 V in normal operation. If separate
analog and digital supplies are used, the recommended decoupling
scheme is shown in Figure 9. In systems where AVDD = 5 V and
DVDD = 5 V, it is recommended that AVDD and DVDD are
driven from the same 5 V supply, although each supply should be
decoupled separately as shown in Figure 9. It is preferable that
the common supply is the system’s analog 5 V supply.
It is also important that power is applied to the AD7711 before
signals at REF IN, AIN, or the logic input pins in order to avoid
latch-up. If separate supplies are used for the AD7711 and the
system digital circuitry, the AD7711 should be powered up first.
If it is not possible to guarantee this, current limiting resistors
should be placed in series with the logic inputs.
AD7711
AVDD
DVDD
0.1 F
10 F
ANALOG
SUPPLY
0.1 F
DIGITAL 5V
SUPPLY
Figure 9. Recommended Decoupling Scheme
DIGITAL INTERFACE
The AD7711’s serial communications port provides a flexible
arrangement to allow easy interfacing to industry-standard
microprocessors, microcontrollers, and digital signal processors.
A serial read to the AD7711 can access data from the output
register, the control register, or the calibration registers. A serial
write to the AD7711 can write data to the control register or the
calibration registers.
Two different modes of operation are available, optimized for
different types of interfaces where the AD7711 can act either as
master in the system (it provides the serial clock) or as slave (an
external serial clock can be provided to the AD7711). These
two modes, labelled self-clocking mode and external clocking
mode, are discussed in detail in the following sections.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC486CSW | IC DVR RS485 LOW PWR QUAD 16SOIC |
| IDT72231L25JI | IC FIFO SYNC 512X9 25NS 32PLCC |
| LTC2221CUP#PBF | IC ADC 12-BIT 135MSPS 64-QFN |
| MS27467E17A26SB | CONN PLUG 26POS STRAIGHT W/SCKT |
| MS27473T24A61PD | CONN PLUG 61POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7711AR | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7711AR-REEL | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7711AR-REEL7 | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD7711ARZ | 功能描述:IC ADC 24BIT RTD I SOURCE 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7711ARZ | 制造商:Analog Devices 功能描述:LC 2MOS SIGNAL CONDITIONING ANALOG/DIGIT |
发布紧急采购，3分钟左右您将得到回复。