收藏本站
参数资料
型号： AD7731BRUZ
厂商： Analog Devices Inc
文件页数： 2/44页
文件大小： 0K
描述： IC ADC 24BIT SIGMA-DELTA 24TSSOP
标准包装： 1
位数： 24
采样率（每秒）： 6.4k
数据接口： DSP，串行，SPI?
转换器数目： 1
功率耗散（最大）： 125mW
电压电源： 模拟和数字
工作温度： -40°C ~ 85°C
安装类型： 表面贴装
封装/外壳： 24-TSSOP（0.173"，4.40mm 宽）
供应商设备封装： 24-TSSOP
包装： 管件
输入数目和类型： 3 个差分，单极；3 个差分，双极；5 个伪差分，单极；5 个伪差分，双极
产品目录页面： 779 (CN2011-ZH PDF)
配用： EVAL-AD7731EBZ-ND - BOARD EVALUATION FOR AD7731
AD7731
–10–
REV. 0
OUTPUT NOISE AND RESOLUTION SPECIFICATION
The AD7731 has a number of different modes of operation of the on-chip filter and chopping features. These options are discussed
in more detail in later sections. The part can be programmed either to optimize the throughput rate and settling time or to optimize
noise and drift performance. Noise tables for two of the primary modes of operation of the part are outlined below for a selection of
output rates and settling times. The first mode, where the AD7731 is configured with CHP = 0 and SKIP mode enabled, provides
fast settling time while still maintaining high resolution. The second mode, where CHP = 1 and the full second filter is included,
provides very low noise numbers with lower output rates. Settling time refers to the time taken to get an output that is 100% settled
to the new value after a channel change or exercising
SYNC.
Output Noise (CHP = 0, SKIP = 1)
Table I shows the output rms noise for some typical output update rates and –3 dB frequencies for the AD7731 when used in
nonchop mode (CHP of Filter Register = 0) and with the second filter bypassed (SKIP of Filter Register = 1). The table is generated
with a master clock frequency of 4.9152 MHz. These numbers are typical and generated at a differential analog input voltage of 0V.
The output update rate is selected via the SF0 to SF11 bits of the Filter Register. Table II, meanwhile, shows the output peak-to-
peak resolution in bits (rounded to the nearest 0.5 LSB) for the same output update rates. It is important to note that the numbers in
Table II represent the resolution for which there will be no code flicker within a six-sigma limit. They are not calculated based on
rms noise but on peak-to-peak noise.
The numbers are generated for the bipolar input ranges. When the part is operated in unipolar mode, the output noise will be the
same as the equivalent bipolar input range. As a result, the numbers in Table I will remain the same for unipolar ranges. To calculate
the numbers for Table II for unipolar input ranges simply subtract one from the peak-to-peak resolution number in bits.
Table I. Output Noise vs. Input Range and Update Rate (CHP = 0, SKIP = 1)
Typical Output RMS Noise in
V
Output
–3 dB
SF
Settling
Input Range
Data Rate
Frequency
Word
Time
1.28 V
640 mV
320 mV
160 mV
80 mV
40 mV
20 mV
150 Hz
39.3 Hz
2048
20 ms
2.6
1.45
0.87
0.6
0.43
0.28
0.2
200 Hz
52.4 Hz
1536
15 ms
3.0
1.66
1.02
0.69
0.48
0.32
0.22
300 Hz
78.6 Hz
1024
10 ms
3.7
2
1.26
0.84
0.58
0.41
0.28
400 Hz
104.8 Hz
768
7.5 ms
4.2
2.3
1.46
1.0
0.69
0.46
0.32
600 Hz
157 Hz
512
5 ms
5.2
2.9
1.78
1.2
0.85
0.58
0.41
800 Hz
209.6 Hz
384
3.75 ms
6
3.3
2.1
1.4
0.98
0.66
0.47
1200 Hz
314 Hz
256
2.5 ms
7.8
4.3
2.6
1.8
1.27
0.82
0.57
1600 Hz
419.2 Hz
192
1.87 ms
10.9
5.4
3.5
2.18
1.51
0.94
0.64
2400 Hz
629 Hz
128
1.25 ms
27.1
13.9
7.3
3.5
2.22
1.24
0.83
3200 Hz
838.4 Hz
96
0.94 ms
47
24.4
11.4
5.3
3.1
1.9
1.0
4800 Hz
1260 Hz
64
0.625 ms
99
50.3
24.5
12.5
6.5
3.3
1.7
6400 Hz
1676 Hz
48
0.47 ms
193
97
48
24
11.8
6.6
3.0
Table II. Peak-to-Peak Resolution vs. Input Range and Update Rate (CHP = 0, SKIP = 1)
Peak-to-Peak Resolution in Bits
Output
–3 dB
SF
Settling
Input Range
Data Rate
Frequency
Word
Time
1.28 V
640 mV
320 mV
160 mV
80 mV
40 mV
20 mV
150 Hz
39.3 Hz
2048
20 ms
17.5
17
16.5
16
15.5
15
200 Hz
52.4 Hz
1536
15 ms
17
16.5
16
15.5
15
300 Hz
78.6 Hz
1024
10 ms
17
16.5
16
15.5
15
14.5
400 Hz
104.8 Hz
768
7.5 ms
16.5
16
15.5
15
14.5
600 Hz
157 Hz
512
5 ms
16.5
16
15.5
15
14.5
14
800 Hz
209.6 Hz
384
3.75 ms
16
15.5
15
14.5
14
1200 Hz
314 Hz
256
2.5 ms
15.5
15
14.5
14
13.5
1600 Hz
419.2 Hz
192
1.87 ms
15
15.5
15
14.5
14
13.5
2400 Hz
629 Hz
128
1.25 ms
14
13.5
13
3200 Hz
838.4 Hz
96
0.94 ms
13
12.5
4800 Hz
1260 Hz
64
0.625 ms
12
11.5
12
6400 Hz
1676 Hz
48
0.47 ms
11
REV. A
相关PDF资料
PDF描述
MAX9031AUK-T IC COMPARATOR VOLT SGL SOT23-5
VI-J54-MY-F2 CONVERTER MOD DC/DC 48V 50W
VE-2NY-IV-B1 CONVERTER MOD DC/DC 3.3V 99W
HIN202CBZ-T IC 2DRVR/2RCVR RS232 5V 16-SOIC
VI-J5K-MY-F2 CONVERTER MOD DC/DC 40V 50W
相关代理商/技术参数
参数描述
AD7731BRUZ-REEL 功能描述:IC ADC 24BIT SIGMA-DELTA 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
AD7731BRUZ-REEL7 功能描述:IC ADC 24BIT SIGMA-DELTA 24TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
AD7731BRZ 功能描述:IC ADC 24BIT SIGMA-DELTA 24-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6
AD7731BRZ 制造商:Analog Devices 功能描述:IC ADC 24BIT 5MSPS SOIC-24
AD7731BRZ-REEL 功能描述:IC ADC 24BIT SIGMA-DELTA 24-SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*