- 您现在的位置：买卖IC网 > PDF目录10218 > AD7856ARSZ-REEL7 (Analog Devices Inc)IC ADC 14BIT 8CHAN 5V 24SSOP PDF资料下载
参数资料
| 型号： | AD7856ARSZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 8CHAN 5V 24SSOP |
| 标准包装： | 500 |
| 位数： | 14 |
| 采样率（每秒）： | 285k |
| 数据接口： | 8051，QSPI?，串行，SPI? µP |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；4 个伪差分，单极 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7856
–13–
REV. A
CALIBRATION REGISTERS
The AD7856 has ten calibration registers in all, eight for the
DAC, one for the offset and one for gain. Data can be written
to or read from all ten calibration registers. In self- and system
calibration the part automatically modifies the calibration regis-
ters; only if the user needs to modify the calibration registers
should an attempt be made to read from and write to the cali-
bration registers.
Addressing the Calibration Registers
The calibration selection bits in the control register CALSLT1
and CALSLT0 determine which of the calibration registers are
addressed (see Table V). The addressing applies to both the
read and write operations for the calibration registers. The user
should not attempt to read from and write to the calibration
registers at the same time.
Table V. Calibration Register Addressing
CALSLT1
CALSLT0
Comment
0
This combination addresses the
Gain (1), Offset (1) and DAC Reg-
isters (8). Ten registers in total.
0
1
This combination addresses the
Gain (1) and Offset (1) Registers.
Two registers in total.
1
0
This combination addresses the
Offset Register. One register in
total.
1
This combination addresses the
Gain Register. One register in total.
Writing to/Reading from the Calibration Registers
For writing to the calibration registers a write to the control
register is required to set the CALSLT0 and CALSLT1 bits.
For reading from the calibration registers a write to the control
register is required to set the CALSLT0 and CALSLT1 bits,
but also to set the RDSLT1 and RDSLT0 bits to 10 (this ad-
dresses the calibration registers for reading). The calibration
register pointer is reset upon writing to the control register
setting the CALSLT1 and CALSLT0 bits, or upon completion
of all the calibration register write/read operations. When reset,
it points to the first calibration register in the selected write/
read sequence. The calibration register pointer will point to the
gain calibration register upon reset in all but one case, this case
being where the offset calibration register is selected on its own
(CALSLT1 = 1, CALSLT0 = 0). Where more than one cali-
bration register is being accessed the calibration register pointer
will be automatically incremented after each calibration register
write/read operation. The order in which the ten calibration
registers are arranged is shown in Figure 7. The user may abort
at any time before all the calibration register write/read opera-
tions are completed, and the next control register write opera-
tion will reset the calibration register pointer. The flowchart in
Figure 8 shows the sequence for writing to the calibration regis-
ters and Figure 9 for reading.
CAL REGISTER
ADDRESS POINTER
GAIN REGISTER
OFFSET REGISTER
DAC 1ST MSB REGISTER
DAC 8TH MSB REGISTER
.
(1)
(2)
(3)
(10)
CALIBRATION REGISTERS
CALIBRATION REGISTER
ADDRESS POINTER
POSITION IS DETERMINED
BY THE NUMBER OF
CALIBRATION REGISTERS
ADDRESSED AND THE
NUMBER OF READ/WRITE
OPERATIONS
Figure 7. Calibration Register Arrangements
When reading from the calibration registers there will always be
two leading zeros for each of the registers. When operating in
Serial Interface Mode 1 the read operations to the calibration
registers cannot be aborted. The full number of read operations
must be completed (see section on Serial Interface Mode 1
Timing for more detail).
START
WRITE TO CONTROL REGISTER SETTING STCAL = 0
AND CALSLT1, CALSLT0 = 00, 01, 10, 11
CAL REGISTER POINTER IS
AUTOMATICALLY RESET
WRITE TO CAL REGISTER
(ADDR1 = 1, ADDR0 = 0)
CAL REGISTER POINTER IS
AUTOMATICALLY INCREMENTED
LAST
REGISTER
WRITE
OPERATION
OR
ABORT
?
FINISHED
YES
NO
Figure 8. Flowchart for Writing to the Calibration
Registers
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21J-IU-F3 | CONVERTER MOD DC/DC 36V 200W |
| CS8416-CNZ | IC RCVR DGTL 192KHZ 28QFN COMM |
| VI-21J-IU-F2 | CONVERTER MOD DC/DC 36V 200W |
| SP3494EN-L/TR | IC TXRX RS485/RS422 LP 8NSOIC |
| SP3491EN-L/TR | IC TXRX RS485 FULL DUPLX 14NSOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7856ARZ | 功能描述:IC ADC 14BIT 8CHAN 5V 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7856ARZ-REEL7 | 功能描述:IC ADC 14BIT 8CHAN 5V 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD7856KR | 制造商:Analog Devices 功能描述:ADC Single SAR 285ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:8 CH. 14-BIT 300 KSPS ADC I.C. - Bulk |
| AD7856KR-REEL | 功能描述:IC ADC 14BIT 8CH 5V 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7856KR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 285ksps 14-bit Serial 24-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:8 CH. 14-BIT 300 KSPS ADC I.C. - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。