- 您现在的位置：买卖IC网 > PDF目录10218 > AD7856ARSZ-REEL7 (Analog Devices Inc)IC ADC 14BIT 8CHAN 5V 24SSOP PDF资料下载
参数资料
| 型号： | AD7856ARSZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 8CHAN 5V 24SSOP |
| 标准包装： | 500 |
| 位数： | 14 |
| 采样率（每秒）： | 285k |
| 数据接口： | 8051，QSPI?，串行，SPI? µP |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 89.25mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 8 个单端，单极；4 个伪差分，单极 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7856
–16–
REV. A
ANALOG INPUT
The equivalent circuit of the analog input section is shown in
Figure 11. During the acquisition interval the switches are both
in the track position and the AIN(+) charges the 20 pF capaci-
tor through the 125
resistance. On the rising edge of CONVST
switches SW1 and SW2 go into the hold position retaining
charge on the 20 pF capacitor as a sample of the signal on
AIN(+). The AIN(–) is connected to the 20 pF capacitor, and
this unbalances the voltage at node A at the input of the com-
parator. The capacitor DAC adjusts during the remainder of the
conversion cycle to restore the voltage at node A to the correct
value. This action transfers a charge, representing the analog
input signal, to the capacitor DAC which in turn forms a digital
representation of the analog input signal. The voltage on the
AIN(–) pin directly influences the charge transferred to the
capacitor DAC at the hold instant. If this voltage changes dur-
ing the conversion period, the DAC representation of the analog
input voltage will be altered. Therefore it is most important that
the voltage on the AIN(–) pin remains constant during the con-
version period. Furthermore, it is recommended that the AIN(–)
pin is always connected to AGND or to a fixed dc voltage.
CAPACITOR
DAC
COMPARATOR
HOLD
TRACK
SW2
NODE A
20pF
SW1
TRACK
HOLD
125
AIN(+)
AIN(–)
CREF2
125
Figure 11. Analog Input Equivalent Circuit
Acquisition Time
The track and hold amplifier enters its tracking mode on the
falling edge of the BUSY signal. The time required for the track
and hold amplifier to acquire an input signal will depend on
how quickly the 20 pF input capacitance is charged. The acqui-
sition time is calculated using the formula:
tACQ = 10
× (R
IN + 125
) × 20 pF
where RIN is the source impedance of the input signal, and
125
, 20 pF is the input RC.
DC/AC Applications
For dc applications high source impedances are acceptable
provided there is enough acquisition time between conversions
to charge the 20 pF capacitor. The acquisition time can be
calculated from the above formula for different source imped-
ances. For example, with RIN = 5 k the required acquisition
time will be 1025 ns.
For ac applications, removing high frequency components from
the analog input signal is recommended by use of an RC low-
pass filter on the AIN(+) pin as shown in Figure 13. In applica-
tions where harmonic distortion and signal-to-noise ratio are
critical, the analog input should be driven from a low impedance
source. Large source impedances will significantly affect the ac
performance of the ADC. This may necessitate the use of an
input buffer amplifier. The choice of the op amp will be a func-
tion of the particular application.
When no amplifier is used to drive the analog input the source
impedance should be limited to low values. The maximum
source impedance will depend on the amount of total harmonic
distortion (THD) that can be tolerated. The THD will increase
as the source impedance increases and performance will de-
grade. Figure 12 shows a graph of the total harmonic distortion
versus analog input signal frequency for different source imped-
ances. With the setup as in Figure 13, the THD is at the –90 dB
level. With a source impedance of 1 k
and no capacitor on the
AIN(+) pin, the THD increases with frequency.
THD
–
dB
INPUT FREQUENCY – kHz
–50
–60
–110
–100
–80
–90
–70
1
166
10
20
50
80
RIN = 560
RIN = 10 , 10nF
AS IN FIGURE 13
140
120
100
THD VS. FREQUENCY FOR DIFFERENT
SOURCE IMPEDANCES
Figure 12. THD vs. Analog Input Frequency
In a single supply application (5 V), the V+ and V– of the op
amp can be taken directly from the supplies to the AD7856
which eliminates the need for extra external power supplies.
When operating with rail-to-rail inputs and outputs, at frequen-
cies greater than 10 kHz care must be taken in selecting the
particular op amp for the application. In particular for single
supply applications the input amplifiers should be connected in
a gain of –1 arrangement to get the optimum performance.
Figure 13 shows the arrangement for a single supply application
with a 50
and 10 nF low-pass filter (cutoff frequency 320 kHz)
on the AIN(+) pin. Note that the 10 nF is a capacitor with good
linearity to ensure good ac performance. Recommended single
supply op amp is the AD820.
AD820
0.1 F
10 F
V+
V–
10k
50
10nF
(NPO)
TO AIN(+)
OF
AD7856
VIN
(0 TO VREF)
VREF
10k
+5V
IC1
Figure 13. Analog Input Buffering
Input Range
The analog input range for the AD7856 is 0 V to VREF. The
AIN(–) pin on the AD7856 can be biased up above AGND, if
required. The advantage of biasing the lower end of the analog
input range away from AGND is that the user does not need to
have the analog input swing all the way down to AGND. This
has the advantage in true single supply applications that the
input amplifier does not need to swing all the way down to
AGND. The upper end of the analog input range is shifted up
by the same amount. Care must be taken so that the bias ap-
plied does not shift the upper end of the analog input above the
AVDD supply. In the case where the reference is the supply,
AVDD, the AIN(–) must be tied to AGND.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-21J-IU-F3 | CONVERTER MOD DC/DC 36V 200W |
| CS8416-CNZ | IC RCVR DGTL 192KHZ 28QFN COMM |
| VI-21J-IU-F2 | CONVERTER MOD DC/DC 36V 200W |
| SP3494EN-L/TR | IC TXRX RS485/RS422 LP 8NSOIC |
| SP3491EN-L/TR | IC TXRX RS485 FULL DUPLX 14NSOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7856ARZ | 功能描述:IC ADC 14BIT 8CHAN 5V 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 其它有关文件:TSA1204 View All Specifications 标准包装:1 系列:- 位数:12 采样率（每秒）:20M 数据接口:并联 转换器数目:2 功率耗散（最大）:155mW 电压电源:模拟和数字 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-TQFP 供应商设备封装:48-TQFP（7x7） 包装:Digi-Reel® 输入数目和类型:4 个单端，单极；2 个差分，单极 产品目录页面:1156 (CN2011-ZH PDF) 其它名称:497-5435-6 |
| AD7856ARZ-REEL7 | 功能描述:IC ADC 14BIT 8CHAN 5V 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| AD7856KR | 制造商:Analog Devices 功能描述:ADC Single SAR 285ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:8 CH. 14-BIT 300 KSPS ADC I.C. - Bulk |
| AD7856KR-REEL | 功能描述:IC ADC 14BIT 8CH 5V 24-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7856KR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 285ksps 14-bit Serial 24-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:8 CH. 14-BIT 300 KSPS ADC I.C. - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。